Gardena V1 Gebruiksaanwijzing - Pagina 3

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Gardena V1. Gardena V1 6 pagina's. Valve box
Ook voor Gardena V1: Gebruiksaanwijzing (10 pagina's), Gebruikershandleiding (11 pagina's), Gebruiksaanwijzing (9 pagina's)

Pagina afdrukken

2. For underground installation, place a layer of course gravel

approx. 20 x 30 x 10 cm

neath the valve box. This ensures proper drainage of the box.

3. Install the valve box with the top edge of the box at ground

level. This avoids damage when mowing the lawn.

Connect GARDENA connect-

You can use the GARDENA Connecting Pipe Art. No. 1580 /

ing pipes to valve box :

1582

and GARDENA Hose Clips Art. No. 1591

the valve box.

1. Push the nipples

2. Fasten the nipples

the nuts

3. Screw a tap connector

4. Push a hose clip

Tip : Place the pipe ends

3 4

push the ends of the pipes

5. Push the connecting pipes

secure with the hose clips

Note : You can also attach a GARDENA Connector Art. No.

2745/ 2749

connecting hard connecting pipes or other commercially avail-

able connecting pipes.

After connecting the pipes to the valve box, the system must be

flushed.

Flash the system :

Flushing the system after routing the pipes prevents contaminating

the valves.

1. Push the long telescopic pipe

on the outlet-side

2. Push the flushing pipe

3. Push the bracket

the inlet-side

The flushing pipe

4. Screw the long telescopic pipe

5 a

5. Turn on the water supply at the nipple

The system is flushed.

6. Remove the flushing pipe

(V 1) / 30 x 35 x 10 cm

(V 2) under-

to connect

from the inside into the box openings.

to the valve box from the outside using

on each nipple

over each pipe end

in warm water to make it easier to

onto the tap connectors

(1 " = 25 mm / 5 /4 " = 32 mm) to the nipples

all the way into the nipple

into the nipple on the inlet-side

into the elongated holes of the nipple on

is fixed in place.

onto the flushing pipe

Close off nipple

on inlet-side :

Assemble the

Irrigation Valve :

and

for

A C

Lock the box lid :

Connect Soil Moisture

Sensor or Rain Sensor

electronic (optional) :

If you connect several Irrigation Valves to one water supply, then

each pipe must be flushed separately in order to obtain an ade-

quate flushing pressure. To do this:

1. Push the short telescopic pipe

side

which is not to be flushed.

2. Push the bracket

into the elongated holes of the nipple on

the inlet-side

The short telescopic tube

3. Screw the end cap

onto the short telescopic pipe

The integrated solenoid valve only works correctly with the

Irrigation Valve connected in flow direction.

Flow direction

V Pay attention to the flow direction (arrows) when

assembling the Irrigation Valve

1. Push the long telescopic pipe

on the outlet-side

2. Screw the short telescopic pipe

Irrigation Valve

The arrows on the Irrigation Valve point in the flow direction.

3. Push the short telescopic pipe

side

4. Screw the long telescopic pipe

Irrigation Valve

5. Push the bracket

into the elongated holes of the nipples

5 a

The telescopic pipes

When you open the box lid

marked by the arrows on the Irrigation Valve

v The box lid

can be locked by turning the lever

The box lid

can be locked as a protection against theft.

v Overlap the holes

of the valve box and the box lid and lock

using a small padlock

– or –

alternatively, the lid

can be safeguarded against theft using

a sheet metal screw (4.2 x 19).

In conjunction with the programmed watering time, the moisture

level of the soil or the natural precipitation can be taken into

account for each Irrigation Valve.

When a sufficient moisture content of the soil is reached, a pro-

gramme may be interrupted or activation of a programme may

be suppressed.

into the nipple on the inlet-

is fixed in place.

all the way into the nipple

into the inlet side of the

into the nipple on the inlet-

into the outlet-side of the

are fixed in place.

you can see the flow direction

by 90°.