Makita 6095D Gebruiksaanwijzing - Pagina 4

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Makita 6095D. Makita 6095D 14 pagina's. Cordless driver drill
Ook voor Makita 6095D: Onderdelenlijst (3 pagina's), Gebruiksaanwijzing (15 pagina's)

Pagina afdrukken

IMPORTANT SAFETY

INSTRUCTIONS FOR BATTERY

CARTRIDGE

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively shorter,

stop operating immediately. It may result in a risk

of overheating, possible burns and even an explo-

sion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Always cover the battery terminals with the bat-

tery cover when the battery cartridge is not used.

6. Do not short the battery cartridge:

(1) Do not touch the terminals with any conduc-

tive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a break-

down.

7. Do not store the tool and battery cartridge in loca-

tions where the temperature may reach or exceed

50°C (122°F).

8. Do not incinerate the battery cartridge even if it is

severely damaged or is completely worn out. The

battery cartridge can explode in a fire.

9. Be careful not to drop or strike battery.

SAVE THESE INSTRUCTIONS

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice less

tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room tempera-

ture at 10°C - 40°C (50°F - 104°F). Let a hot battery

cartridge cool down before charging it.

4. Charge the Nickel Metal Hydride battery cartridge

when you do not use it for more than six months.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before adjusting or checking

function on the tool.

Installing or removing battery cartridge

(Fig. 1)

• Always switch off the tool before insertion or removal of

ENC004-1

the battery cartridge.

• To remove the battery cartridge, pull out the set plate

on the tool and grasp both sides of the cartridge while

withdrawing it from the tool.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Snap the set plate back into place. Be sure

to close the set plate fully before using the tool to pre-

vent the battery cartridge from accidentally falling out of

the tool.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Switch action (Fig. 2)

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the "OFF" position when

released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

Reversing switch action (Fig. 3)

This tool has a reversing switch to change the direction of

rotation. Slide the reversing switch to the right (appear "F"

marking) for clockwise rotation or to the left (appear "R"

marking) for counterclockwise rotation.

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

Speed change (Fig. 4)

To change the speed, turn the speed change knob so that

the arrow of the desired speed on the knob is aligned with

the reference arrow on the tool body. If the speed change

knob does not turn easily, switch on the tool and turn the

knob again while the tool is running under no load. Be

sure that the speed change knob is set to the correct posi-

tion before operation. Use the right speed for your job.

Adjusting the fastening torque (Fig. 5)

The fastening torque can be adjusted in 6 steps by turning

the adjusting ring so that the pointer on the adjusting ring

points to a number on the tool body. The fastening torque

is minimum when the pointer points to the number 1 and

maximum when it points to the

The clutch will slip at various torque levels when set at the

number 1 to 5. The clutch is designed not to slip at the

marking.

Before actual operation, drive a trial screw into your mate-

rial or a piece of duplicate material to determine which

torque level is required for a particular application.

marking.