Garmin Zumo 590 Gebruikershandleiding - Pagina 17
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Garmin Zumo 590. Garmin Zumo 590 26 pagina's. Zumo 590
Ook voor Garmin Zumo 590: Snelstarthandleiding (6 pagina's), Gebruikershandleiding (26 pagina's), Handleiding voor installatie-instructies (36 pagina's), Handleiding voor installatie-instructies (46 pagina's)
Pagina afdrukken
11
On the sensor, affix the numerical sticker that corresponds to
the tire number you selected in step 6.
12
Repeat this procedure for each remaining sensor.
Installing the Sensors on Your Tires
The Tire Pressure Monitor System is for use with metal tire
valve stems only. Installation of the Tire Pressure Sensors on
non-metal tire valve stems may cause tire and/or tire valve stem
damage which could result in serious personal injury or death.
To prevent possible damage to the sensors or vehicle, ensure
each installed sensor does not interfere with the vehicle brakes,
suspension components, or other installed equipment. If an
installed sensor interferes with any installed equipment on the
vehicle, do not operate the vehicle with the sensor installed.
To prevent possible tire vibration or uneven tire wear on some
vehicles, it may be necessary to balance the vehicle tires after
installing the sensor.
Before you install the sensors on your tires, you should set up
the sensors with your zūmo device.
1
Remove the existing valve stem caps from your vehicle tires.
2
On your zūmo device, select Apps > Tire Pressure to view
the vehicle profile diagram.
3
Install the sensors onto the tire valve stems by tightening
them clockwise.
NOTE: You must install each sensor onto the correct tire
based on the vehicle profile diagram and the numerical
stickers affixed to the sensors during the setup process.
4
Rotate the wheels by hand to verify the sensors have
adequate clearance and do not interfere with vehicle
equipment.
Tire Pressure Alerts
The device alerts you using pop-up messages, icons on the
map, and symbols in the tire pressure app.
When an alert exists for a sensor, the number next to the
corresponding tire appears red in the tire pressure app. The
symbols below the number appear red to indicate the active
alerts for that sensor.
Low tire pressure
Low sensor battery
Sensor not connected
Tire Pressure Sensor Sleep Mode
When you park your vehicle and turn off your zūmo device, the
tire pressure sensor enters a power-saving sleep mode after
several minutes. The sensor does not transmit information to
the zūmo device while in sleep mode. This can cause your
zūmo device to report the sensor is disconnected.
The next time your vehicle moves, the sensor exits sleep mode
and automatically reconnects to the zūmo device. It may take
up to 30 seconds to reconnect.
Using the Compass
NOTE: You must be moving for the compass to determine your
direction.
You can navigate using a GPS compass.
Select Apps > Compass.
Using the Apps
WARNING
NOTICE
VIRB Remote
The VIRB™ remote function allows you to control your VIRB
action camera from a distance. Go to
purchase a VIRB action camera.
Controlling a VIRB Action Camera
Before you can use the VIRB remote function, you must enable
the remote setting on your VIRB camera. See the VIRB Series
Owner's Manual for more information.
1
Turn on your VIRB camera.
2
On your zūmo device, select Apps > VIRB Remote >
Connect.
3
Wait while the device connects to your VIRB camera.
4
Select an option:
• Select Start Recording to record video.
• Select Stop Recording to stop recording video.
• Select Snapshot to take a photograph.
Finding Your Last Parking Spot
When you disconnect the device from vehicle power while the
device is on, your current location is saved as a parking spot.
Select Apps > Last Spot.
Viewing Previous Routes and Destinations
Before you can use this feature, you must enable the travel
history feature
(Device and Privacy
You can view your previous routes and places you have
stopped on the map.
Select Apps > Where I've Been.
Logging Service History
You can log the date and odometer reading when service or
maintenance is performed on your vehicle. The device provides
several service categories, and you can add custom categories
(Adding Service
Categories).
1
Select Apps > Service History.
2
Select a service category.
3
Select Add Record.
4
Enter the odometer reading, and select Next.
5
Enter a comment (optional).
6
Select Done.
Adding Service Categories
1
Select Apps > Service History.
2
Select
> Add Category.
3
Enter a category name, and select Done.
Deleting Service Categories
When you delete a service category, all service records in the
category are also deleted.
1
Select Apps > Service History.
2
Select
> Delete Categories.
3
Select the service categories to delete.
4
Select Delete.
Renaming Service Categories
1
Select Apps > Service History.
2
Select the category to be renamed.
3
Select
> Rename Category.
4
Enter a name, and select Done.
Deleting Service Records
1
Select Apps > Service History.
www.garmin.com/VIRB
to
Settings).
13