Garmin VENU 2S Gebruikershandleiding - Pagina 31
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Garmin VENU 2S. Garmin VENU 2S 39 pagina's.
Pagina afdrukken
activity.
Changing the Units of Measure
You can customize the units of measure displayed on the
device.
1 From the watch face, hold
2 Select
> System > Units.
3 Select a measurement type.
4 Select a unit of measure.
Garmin Connect Settings
You can change your device settings from your Garmin
Connect account, using either the Garmin Connect
app or the Garmin Connect website. Some settings are
available only using your Garmin Connect account and
cannot be changed on your device.
From the Garmin Connect app, select or , select
Garmin Devices, and select your device.
From the devices widget in the Garmin Connect
application, select your device.
After customizing settings, sync your data to apply the
changes to your device
(Using the Garmin Connect App, page
21,
Using Garmin Connect on Your Computer, page
Wireless Sensors
Your device can be used with wireless ANT+ sensors. Your
device with music features can also be used with
Bluetooth sensors. For more information about
compatibility and purchasing optional sensors, go to
Garmin.com.sg/buy.
Pairing Your Wireless Sensors
The first time you connect a wireless ANT+ or Bluetooth
sensor to your Garmin device, you must pair the device and
sensor. After they are paired, the device connects to the
sensor automatically when you start an activity and the
sensor is active and within range.
TIP: Some ANT+ sensors pair with your device
automatically when you start an activity with the
sensor turned on and near the device.
1 Move at least 10 m (33 ft.) away from other
wireless sensors.
2 If you are pairing a heart rate monitor, put on the heart
rate monitor.
The heart rate monitor does not send or receive data
until you put it on.
3 Hold
.
4 Select
> Sensors > Add New.
5 Bring the device within 3 m (10 ft.) of the sensor, and
wait while the device pairs with the sensor.
After the device connects to the sensor, an icon
appears at the top of the screen.
26
.
21).
Foot Pod
Your device is compatible with the foot pod. You can use
the foot pod to record pace and distance instead of using
GPS when you are training indoors or when your GPS
signal is weak. The foot pod is on standby and ready to
send data (like the heart rate monitor).
After 30 minutes of inactivity, the foot pod powers off to
conserve the battery. When the battery is low, a message
appears on your device. Approximately five hours of
battery life remain.
Calibrating Your Foot Pod
Before you can calibrate your foot pod, you must pair your
device with the foot pod
page
26).
Manual calibration is recommended if you know your
calibration factor. If you have calibrated a foot pod with
another Garmin product, you may know your calibration
factor.
1 Hold
.
2 Select
> Sensors > Foot Pod > Cal� Factor.
3 Adjust the calibration factor:
• Increase the calibration factor if your distance is too
low.
• Decrease the calibration factor if your distance is too
high.
Improving Foot Pod Calibration
Before you can calibrate your device, you must acquire GPS
signals and pair your device with the foot pod
Your Wireless Sensors, page
The foot pod is self‑ c alibrating, but you can improve the
accuracy of the speed and distance data with a few
outdoor runs using GPS.
1 Stand outside for 5 minutes with a clear view of the
sky.
2 Start a running activity.
3 Run on a track without stopping for 10 minutes.
4 Stop your activity, and save it.
Based on the recorded data, the foot pod calibration
value changes, if necessary. You should not need to
calibrate the foot pod again unless your running style
changes.
Using an Optional Bike Speed or Cadence
Sensor
You can use a compatible bike speed or cadence sensor to
send data to your device.
Pair the sensor with your device
Wireless Sensors, page
Set your wheel size
(Calibrating Your Speed Sensor, page
27).
Go for a ride
(Going for a Ride, page
(Pairing Your Wireless Sensors,
(Pairing
26).
(Pairing Your
26).
15).
Wireless Sensors