Alka Natural Water Alka-Pi Installatiehandleiding - Pagina 4

Blader online of download pdf Installatiehandleiding voor {categorie_naam} Alka Natural Water Alka-Pi. Alka Natural Water Alka-Pi 8 pagina's.

Pagina afdrukken

1. Tubing Connections

------

Diagram A

1. Faucet Installation

Drilling the Faucet Hole

The

product

water faucet

may be installed

any flat

surface

at least 2" in diameter. Check the underside of the location for

interference. Drill

hole through the countertop

where

the faucet will be mounted at least 7/16" (llmm) in diameter. (Most

faucets will mount to a hole diameter of up to 1

'/.,")

Drilling a

lj."

(6mm)

pilot hole first may be helpful. Take

caution

when

drilling the faucet-mounting hole. Different countertops may require

special

drill-bits

and

or installation methods.

AIR

GAP

FAUCETS

Attach

'/.,"

black

waste line

from

to smaller

'/.,"

barb

fitting under faucet.

Air-Gap Faucet

2. Attach the

3/8"

UPFOR

waste line from drain

CONSTANT

FUL

FLOW

saddle to the larger

3/8"

barb

MIDDLE POSITION

:.._~

FOR

OFF

DOWN FOR.

CONTROLLED

FLOW

CHROME '."IASHER

BLACK

WASHER

RUBBER

GASKET

BLACK TUBE

(FAOM

SYSTEM)

318'

BLACK

TUBE

(TO DRAIN

SADDLE)

________

BRASS INLET NIPPLf;

INLET

LINE

BRA

SLEEVE

COMPRESSION

NUT

Note: Some states require the

use ofan air gap

faucet.

Check your local plumbing

code

assure compliance.

Mounting the Faucet

Insert the faucet shank down through the drilled hole. Be sure the faucet body, faucet base,

and

the rubber faucet base washer

are in place above the sink as shown in Diagram A. Install the star lock-washer and nut, and then tigbten firmly while faucet is

aligned in the desired

location.

Do not

over

tighten. Tip: This step may be easier with 2

people. One

person holds the faucet

place

from above,

while

the

other

tightens the

faucet from

underneath.

Note: To connect an additional

point of

use

outlet

(icemaker, extra faucet, etc.) place a tee-fitting

connector

along the line

between the faucet and the RO

system.

A line

can

then be run from the tee to the

outlet

device. Additional fittings andlor

connectors

may be

required.

lcemakers may have proprietary connections and/or

specific

pressure requirements. Check with

your

manufacturer for details

2. Feed Water Assembly

Turn off cold water supply to the

sink

using the supply valve located under tbe

sink.

Different systems

will

come

with

different adapters types

and styles.

Shown below are a few of the most

common

options

Only install to cold water

supplies

and do not over tighten fittings.

Note: Some shut offvalves

have

an extra

port or a separate valve

plumbedfor an icemaker

or filter system. In

either

ofth

ese

cases you will not need the

feedwater

adapter, just hook the feed line directly

this access point.

Scenario 1 Plastic Feed Water

Make sure the black washer is seated in the feedwater adapter. Tighten feedwater

adapter

to the valve with an adjustable

wrench. Tighten until

snug

but do not over tighten. Connect the tubing feed line (usually red in color) by plugging the tubing

end into the feed water connector

collet,

cut the tubing line anywhere along

it,

and install the inline ball valve, again by

pushing the tubing

ends securely

into the collets.