Garmin GPSMAP 3205 - Marine GPS Receiver Handleiding voor installatie-instructies - Pagina 2

Blader online of download pdf Handleiding voor installatie-instructies voor {categorie_naam} Garmin GPSMAP 3205 - Marine GPS Receiver. Garmin GPSMAP 3205 - Marine GPS Receiver 10 pagina's. Declaration of conformity
Ook voor Garmin GPSMAP 3205 - Marine GPS Receiver: Snelle referentiehandleiding (2 pagina's), Handleiding voor installatie-instructies (17 pagina's), Sjabloonhandleiding (1 pagina's), Belangrijke veiligheidsinformatie (48 pagina's), Conformiteitsverklaring (1 pagina's)

Garmin GPSMAP 3205 - Marine GPS Receiver Handleiding voor installatie-instructies
To install the bail-mount bracket
1. Using the bail mount as a template, mark the location of the four mounting holes. Be sure to leave at least 2 in. (5.1 cm) of clearance behind
the GPSMAP 3000 series chartplotter for the wiring.
NotE: Mount a GPSMAP 3005C/3205C chartplotter 10 in. (25 cm), a GPSMAP 3006/3206C chartplotter 12 in. (30 cm), and a
GPSMAP 3010C/3210C chartplotter 24 in. (60 cm) from a magnetic compass to avoid interference.
2. Using an appropriately sized drill bit, drill the pilot holes for your mounting hardware.
3. Secure the bail mount to the surface with your mounting hardware.
To install the GPSMAP 3000 series chartplotter on the bail-mount bracket
1. Loosely attach the mounting knobs to the GPSMAP 3000 series chartplotter.
2. Slide the chartplotter onto the bail mount, and tighten the mounting knobs.
Flush Mounting the GPSMAP 3000 Series Chartplotter
Use the included flush-mount template and hardware to flush mount your GPSMAP 3000 series chartplotter.
NotE: Make sure the surface on which you mount the chartplotter has at least 2 in. (5.1 cm) of open space behind it to fit the chartplotter and the
connected wires.
NotE: Mount a GPSMAP 3005C/3205C chartplotter 10 in. (25 cm), a GPSMAP 3006/3206C chartplotter 12 in. (30 cm), and a
GPSMAP 3010C/3210C chartplotter 24 in. (60 cm) from a magnetic compass to avoid interference.
Hardware (included):
• Flush-mount template
• Four threaded mounting studs
• Four flat washers
• Eight hex nuts
To flush mount a GPSMAP 3000 series chartplotter:
1. The flush-mount template is included in the product box. Trim the template and ensure it will fit in the location at which you want to flush
mount the chartplotter.
2. Trim the flush-mount template and tape it to the location at which you want to mount the chartplotter.
3. Using a
/
in. (10 mm) drill bit, drill one or more of the four pilot holes inside the corner of the template to begin cutting the mounting surface.
3
8
:
:
Mounting knobs
Tools required (not included):
• Jigsaw
• Masking tape
• Scissors
• Drill
• Drill bits—
/
" (3 mm) and
1
8
/
in. (2 mm) Allen (Hex) wrench
1
16
• 4 mm socket or wrench
• Marker
• Center punch and hammer
RANGE
PAGE
QUIT
ENTER
MARK
ADJ
NAV
MENU
MOB
DATA
CNFG
FCTN
FIND
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
+
-
0
/
" (6 mm)
3
8
GPSMAP 3000 Series Installation Instructions
Bail mount