Garmin GPSMAP 5208 - Marine GPS Receiver Handleiding voor installatie-instructies - Pagina 7

Blader online of download pdf Handleiding voor installatie-instructies voor {categorie_naam} Garmin GPSMAP 5208 - Marine GPS Receiver. Garmin GPSMAP 5208 - Marine GPS Receiver 25 pagina's. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Ook voor Garmin GPSMAP 5208 - Marine GPS Receiver: Belangrijke veiligheidsinformatie (4 pagina's), Snelle referentiehandleiding (2 pagina's), Gebruikershandleiding (2 pagina's), Gebruikershandleiding (2 pagina's), Technische referentie (30 pagina's), Handleiding voor installatie-instructies (19 pagina's), Handleiding voor installatie-instructies (25 pagina's), Snelle referentiehandleiding (2 pagina's), Conformiteitsverklaring (1 pagina's), Handleiding voor afdrukken (2 pagina's), Supplement handleiding (24 pagina's), Gebruikershandleiding (6 pagina's)

Pagina afdrukken
Garmin GPSMAP 5208 - Marine GPS Receiver Handleiding voor installatie-instructies
4. At the marked location, use a
5. Fasten the marine pole mount to the boat (hardware not included).
6. Thread the pole-mount bracket
Do not overtighten the bracket.
7. Route a NMEA 2000 drop cable through the pole-mount bracket and the pole, and connect the cable to the antenna.
8. Place the antenna on the pole-mount bracket, and twist it clockwise
9. Secure the antenna to the bracket with the included M3 set screw
10. R oute the NMEA 2000 drop cable away from sources of electronic interference.
11. C onnect the antenna to your NMEA 2000 network.
12. A fter the antenna is installed on the pole mount, fill the vertical cable slot with a marine sealant (optional).
Mounting the Antenna under a Surface
When choosing a location to install the under-deck-mounting bracket, make sure the included screws are not too long for the surface thickness. If the screws
are not appropriate for the surface, you must supply the correct length of M4 screws to avoid damage to the top of the mounting surface.
The antenna can be mounted under a fiberglass surface. Because the antenna has difficulty acquiring cellular signals through metal, it is
recommended that you use the under-deck mount under a fiberglass surface.
1. Identify the mounting location on the fiberglass surface
at the mounting location.
2. Using the under-deck-mounting bracket
on the surface.
➌
3. Use a
/
in. (3.2 mm) bit to drill the three marked pilot holes.
1
8
4. Place the antenna in the bracket, and twist it clockwise to lock it in place.
5. Secure the antenna to the bracket with the included M3 set screw
6. Remove the backing from the adhesive pads
7. Make sure that the bracket aligns with the pilot holes, and adhere the under-deck
mounting bracket to the surface.
8. Using screws of the appropriate length, fasten the bracket to the surface.
9. Connect a NMEA 2000 drop cable to the antenna
10. R oute the NMEA 2000 drop cable away from sources of electronic interference.
11. C onnect the antenna to your NMEA 2000 network.
GPSMAP 4000/5000 Series Installation Instructions
/
in. (19 mm) bit to drill a hole for the cable to pass through.
3
4
onto the marine pole mount.
➊
, and verify correct operation
➊
as a template, mark three pilot-hole locations
➋
on the under-deck mounting bracket.
➎
.
➏
to lock it in place.
➌
.
➍
notice
.
➍
➊
➋
➌
➍
➏
➎
7