Garmin Echo 100 Handleiding voor installatie-instructies - Pagina 4
Blader online of download pdf Handleiding voor installatie-instructies voor {categorie_naam} Garmin Echo 100. Garmin Echo 100 6 pagina's. Flush mount template
Ook voor Garmin Echo 100: Gebruikershandleiding (13 pagina's), Sjabloon (1 pagina's), Gebruikershandleiding (10 pagina's), Gebruikershandleiding (21 pagina's), Gebruikershandleiding (20 pagina's)
Pagina afdrukken
Fastening the Swivel Mount with the cables Installed in the
Mount
1. Feed the cables ➏ through the
when preparing the swivel-mount base.
2. Place the swivel-mount base ➊ on the
mounting surface, route the cables through
the cable pass-through holes ➎, and
loosely fasten the swivel-mount base using
the appropriate screws or bolts ➋.
3. Place the swivel mount ➌ on the swivel-
mount base, but do not fasten it.
4. Place the echo device or cradle into the
swivel mount
(page
4).
5. Pull out enough slack from the power and
transducer cables so that the mount can
fully swivel to the desired positions when
the cables are connected.
6. Remove the echo device or cradle, and the
swivel mount, from the swivel-mount base.
7. Apply marine sealant to the
center hole and to the cable pass-through
holes.
8. Securely fasten the swivel-mount base, using the appropriate screws or
bolts.
9. Place the swivel mount on the swivel-mount base, and fasten it using the
included 10 mm M6×1 Phillips screw ➍.
Fastening the Swivel Mount without the cables Installed in
the Mount
Complete this task only if you do not need to run the
cables through the mounting surface and the mount.
1. Place the swivel-mount base ➊ on the mounting
surface, and fasten it using the appropriate screws
or bolts ➋.
2. Place the swivel mount ➌ on the swivel-mount
base, and fasten it using the included 10 mm
M6×1 Phillips screw ➍.
3. Seal the cable pass-through holes ➎ with marine
sealant.
4
/
in. (16 mm) center hole you drilled
5
8
➌
➋
➊
/
in. (16 mm)
5
8
➋
➊
Installing the echo Device in the Swivel Mount
1. With the locking arm ➊ in the upward position, place the echo
100/150/300c device ➋ or the echo 200/500c/550c cradle ➌ into the
swivel mount ➍.
➍
➋
2. Tilt the mount for the desired viewing angle and press down on the
locking arm.
➏
➎
Installing the cables and connectors
Wiring to Power
1. Route the power cable from the swivel mount to the boat battery or fuse
block.
• If necessary, extend the wires using 20 AWG or larger wire.
• If you connect the power cable to the fuse block, first remove the
inline fuse holder on the red wire.
2. Connect the red wire to the positive terminal on the battery or fuse block,
➍
and connect the black wire to the negative terminal.
connecting the cables to an echo 100/150/300c
On an echo 100/150/300c device, the connectors on the cables are keyed to
fit only in the correct ports on the device.
➌
1. Compare the divot ➊ on the cable connector to the
keying on the device ports to identify the correct port.
2. Push the cable connector into the correct port until the
connector is fully seated.
3. Repeat steps 1 and 2 until all of the cables are connected
➎
to the device.
➌
➊
➍
➍
echo Installation Instructions
➊
➊