Fujitsu 24LMAS1 Installatiehandleiding - Pagina 12

Blader online of download pdf Installatiehandleiding voor {categorie_naam} Fujitsu 24LMAS1. Fujitsu 24LMAS1 17 pagina's. Outdoor unit

Pagina afdrukken

5. FINISHING

Install the insulated pipes so that they do not touch the compressor.

5.1. Installing insulation

• Install insulation material after conducting "3.6. Sealing test".

• To prevent condensation and water droplets, install insulation material on the refrigerant

pipe. (Fig. A)

• Refer to the table to determine the thickness of the insulation material.

Selection of insulation

(Use an insulation material with equal heat transmission rate or below 0.040

W/(m·k))

Relative humidity

[in (mm)]

1/4 (6.35)

3/8 (9.52)

1/2 (12.70)

Pipe

5/8 (15.88)

diameter

3/4 (19.05)

7/8 (22.22)

1 (25.40)

* When the ambient temperature and relative humidity exceed 89.6 °F (32 °C) (DB) and

85% respectively, strengthen the heat insulation of refrigerant pipe.

5.2. Filling with putty

Fill the piping holes and wiring holes with putty (locally purchased) to avoid any gap

(Fig. A). If small animals such as insects enter the external unit, a short circuit may be

caused near electrical components in the service panel.

• If the outdoor unit is installed at a level that is higher than the indoor unit, the water

that has condensed in the 3-way valve of the outdoor unit could travel to the indoor

unit. Therefore, use putty in the space between the pipe and the insulation to prevent

the entry of water to the indoor units.

Fig. A

Putty

6. HOW TO OPERATE DISPLAY UNIT

6.1. Display unit position

Never touch electrical components such as the terminal blocks except the button on

the display board. It may cause a serious accident such as electric shock.

• Once refrigerant charging is completed, be sure to open the valve prior to

performing the local settings. Otherwise, the compressor may fail.

• Discharge any static electricity from your body before touching the push buttons.

Never touch any terminal or pattern of any parts on the control board.

• The positions of the buttons on the outdoor unit control board are shown in the

following figure.

• Various settings can be adjusted by changing push buttons on the board of the outdoor

unit.

En-12

WARNING

Insulation material

Minimum thickness [in (mm)]

70%

75%

80%

or more

5/16 (8)

3/8 (10)

1/2 (13)

3/8 (9)

7/16 (11)

9/16 (14)

3/8 (10)

1/2 (12)

9/16 (15)

3/8 (10)

1/2 (12)

5/8 (16)

3/8 (10)

1/2 (13)

5/8 (16)

7/16 (11)

1/2 (13)

11/16 (17)

7/16 (11)

1/2 (13)

11/16 (17)

WARNING

Insulation

WARNING

CAUTION

85%

6.2. Description of display and buttons

or more

11/16 (17)

11/16 (18)

• The printed characters for the LED display are shown below.

3/4 (19)

13/16 (20)

13/16 (21)

LED display part

7/8 (22)

Button part

Display lamp

(1) POWER / MODE

(2) ERROR

(3) PUMP DOWN

(L1)

(4) LOW NOISE

(L2, L3)

(5) PEAK CUT

(L4, L5, L6)

Button

S134

MODE

S133

SELECT

S132

ENTER

S131

S130

PUMP DOWN

Function or operation method

Lights on while power on. Local setting in out-

Green

door unit or error code is displayed with blink.

Blinks during abnormal air conditioner

Red

operation.

Lights on during pump down operation.

Orange

Lights on during Low noise mode when local

setting is activated. (Lighting pattern of L2 and

Orange

L3 indicates low noise level)

*Refer to the page 13.

Lights on during Peak cut mode when local

setting is activated. (Lighting pattern of L4, L5

Orange

and L6 indicates peak cut level)

*Refer to the page 14.

Function or operation method

To switch between "Local setting" and "Error code

display".

To switch between the individual "Local settings"

and the "Error code displays".

To fix the individual "Local settings" and the "Error

code displays".

EXIT

To return to "Operation status displays."

To start the pump down operation.

LED display

Push buttons