Fujitsu AB A36LBT Series Ontwerp en technische handleiding - Pagina 28

Blader online of download pdf Ontwerp en technische handleiding voor {categorie_naam} Fujitsu AB A36LBT Series. Fujitsu AB A36LBT Series 48 pagina's. Ceiling type

Pagina afdrukken

Fujitsu AB A36LBT Series Ontwerp en technische handleiding

Setting the Filter Sign

• The indoor unit has a sign to inform the user that it is time to

clean the filter.

• Select the time setting for the filter sign display interval in the

table below according to the amount of dust or debris in the

room. (The unit is factory-set to "00").

• If you do not wish the filter sign to be displayed, select the setting

value for "No indication".

Setting Description

Function Number

standard

(2,500 hours)

Long interval

(4,400 hours)

Short interval

(1,250 hours)

No indication

Setting the Cooler Room Temperature Correction

• Depending on the installed environment, the room temperature

sensor may require a correction.

The settings may be selected as shown in the table below.

(The unit is factory-set to "00".)

Setting Description

Function Number

Standard

Lower control

Setting the Heater Room Temperature Correction

• Depending on the installed environment, the room temperature

sensor may require a correction.

The settings may be changed as shown in the table below.

(The unit is factory-set to "00".)

The air conditioner signal code is set to A prior to shipment.

Contact your retailer to change the signal code.

Setting Description

Function Number

Standard

Lower control

Slightly warmer control

Warmer control

Setting Other Functions

• The following settings are also possible, depending on the

operating conditions.

(The unit is factory-set to "00".)

AUTO Restart

Setting Description

Function Number

Yes

Setting record

• Record any changes to the settings in the following table.

Setting

Ceiling height

Filter sign

Cooler room temperature correction

Heater room temperature correction

Auto restart

After completing the FUNCTION SETTING, be sure to turn off the

power and turn it on again.

Setting Value

- (01 - 25) -

13.

SELECTING THE

REMOTE CONTROL UNIT

CODE

When two or more air conditioners are installed in a room and

the remote control unit is operating an air conditioner other than

the one you wish to set, change the signal code of the remote

control unit to operate only the air conditioner you wish to set (four

selections possible).

When two or more air conditioners are installed in a room, please

contact your retailer to set the individual air conditioner signal

codes.

• Confirm the setting of the remote control unit signal code and the

printed circuit board setting.

If these are not confirmed, the remote control unit cannot be used

to operate for the air conditioner.

Selecting the Remote Control Unit Signal Code

Use the following steps to select the signal

code of the remote control unit. (Note that

the air conditioner cannot receive a signal

code if the air conditioner has not been set

for the signal code.)

1 Press the START/STOP button until only

the clock is displayed on the remote

control unit display.

2 Press the MODE button for at least five

seconds to display the current signal

code (initially set to ).

3 Press the SET TEMP. (

) (

change the signal code between

→

Match the code on the display to the air conditioner signal

code.

4 Press the MODE button again to return to the clock display.

The signal code will be changed.

If no buttons are pressed within 30 seconds after the signal

code is displayed, the system returns to the original clock

display. In this case, start again from step 1.

The air conditioner signal code is set to A prior to shipment.

Contact your retailer to change the signal code.

The remote control unit resets to signal code A when the

batteries in the remote control unit are replaced. If you use a

signal code other than signal code A, reset the signal code after

replacing the batteries.

If you do not know the air conditioner signal code setting, try

each of the signal codes (

→

code which operates the air conditioner.

Indoor unit setting

Jumper wire

JM 1

JM 2

Connect

Disconnect

Connect

Disconnect

Indoor unit Printed circuit board

CAUTION

When cutting off the jumper wire, be careful not to damage

the other parts within the printed circuit board.

) button to

→

) until you find the

Remote control unit signal code

A (Primary setting)