Fujitsu UTY-RNRUZ2 Bedieningshandleiding - Pagina 16
Blader online of download pdf Bedieningshandleiding voor {categorie_naam} Fujitsu UTY-RNRUZ2. Fujitsu UTY-RNRUZ2 26 pagina's. Remote controller (wired type)
Ook voor Fujitsu UTY-RNRUZ2: Installatiehandleiding (11 pagina's)
Pagina afdrukken
3-5-5 Away Setting
(1) Touch the [Away] on the "Spe-
cial Setting" screen. When the
"Password Verification" screen
was displayed, enter the pass-
word and touch the [OK].
Enable the Away Setting
(2) "Away Setting" screen is displayed. Touch the [Enable/
Disable] on the "Away Setting" screen.
(3) "Enable/Disable" screen is displayed. Touch the [Enable]
on the "Enable/Disable" screen.
When the [OK] is touched, the display returns to "Away
Setting" screen.
(2)
Away Setting
Enable /Disable
Cool
Heat
Cancel
OK
Set the Start Temp.
(4) Touch the [Start Temp.] on the "Away Setting" screen.
(5) "Operation Temp" screen is displayed. Set the tempera-
ture by touching [ ] or [ ].
When "Cool" or "Heat" is not used, touch the [Not Used].
To reset [Not Used], set the temperature again.
(4)
Away Setting
Enable /Disable
Cool
Heat
Cancel
OK
Notes
• At Away operation, the indoor unit operates at Set Temp
2°F (1°C) lower than the set value so that the room tem-
perature at cooling does not exceed the Start Temp and
at heating, the indoor unit operates at Set Temp 2°F (1°C)
higher than the set value so that the room temperature
does not drop below the Start Temp.
• "Cool" and "Heat" cannot be set to [Not Used] simulta-
neously. In addition, when the indoor unit is a cooling
only model, "Cool" cannot be set to [Not Used].
• When this function is used together with Anti Freeze, set
"Heat" to [Not Used].
When the [OK] is touched, the display returns to "Away Set-
ting" screen.
Apply the setting
(6) Touch the [OK] on the "Away
Setting" screen. After the set-
ting change screen was dis-
played, the display returns to
the "Special Setting" screen.
En-15
Special Setting
Away Setting
Fan Control for
Energy Saving
Previous
Back
Page
(3)
Enable/Disable
[Disable]
Enable
Start Temp.
88
°F
Disable
48
°F
Cancel
(5)
Start Temp.
[Enable]
Cool
Start Temp.
88
88
°F
48
°F
Not Used
°F
Cancel
Away Setting
Enable /Disable
Cool
Heat
Cancel
3-5-6 Human Sensor Setting (for administrator)
(1) Touch the [Human Sensor Setting] on the "Special Set-
Page 2/ 2
ting" screen. When the "Password Verification" screen is
Human Sensor
displayed, enter the password and touch the [OK].
Setting
(2) "Human Sensor Setting" screen is displayed. Touch the
[Auto Saving] or [Auto Off] on the "Human Sensor Set-
ting" screen.
(1)
Special Setting
Fan Control for
Energy Saving
Each setting screen is displayed.
Setting of the Auto Saving
(3) Touch the [Auto Saving] on the "Human Sensor Setting"
screen. "Auto Saving" screen is displayed. Touch the
[Enable/Disable] on the "Auto Saving" screen.
(4) "Enable/Disable" screen is displayed. Touch the [Enable]
OK
on the "Enable/Disable" screen.
(3)
Auto Saving
Enable/Disable
Absence Detection Time
When the [OK] is touched, the display returns to "Auto
Saving" screen.
(5) Touch the [Absence Detection Time] on the "Auto Sav-
Heat
ing" screen.
48
(6) The "Absence Detection Time" screen is displayed. Set
Not Used
°F
the time with [ ] or [ ]. The time can be set to 15, 30,
OK
45, 60, 90, 120 or 180 min.
(5)
Auto Saving
Enable/Disable
Absence Detection Time
Note
When detection time the same as or longer than "Auto
Off" is set at "Auto Saving", "Auto Saving" does not oper-
ate.
When the [OK] is touched, the display returns to the "Auto
Saving" screen. And when the [OK] on the "Auto Sav-
ing" screen is touched, the display returns to the "Human
Sensor Setting" screen.
Setting of the Auto Off
(7) Touch the [Auto Off] on the "Human Sensor Setting"
[Enable]
screen. "Auto Off" screen is displayed. Touch the [En-
Start Temp.
able/Disable] on the "Auto Off" screen.
88
°F
48
°F
(8) "Enable/Disable" screen is displayed. Touch the [Enable]
OK
on the "Enable/Disable" screen.
Page 2/ 2
Human Sensor
Away Setting
Setting
Previous
Back
Page
Fri 10:00AM
[Disable]
[In 30 min.]
Cancel
OK
Fri 10:00AM
[Disable]
[In 30 min.]
Cancel
OK
(2)
Human Sensor Setting
Auto Saving
[Disable]
Auto Off
[Disable]
Back
(4)
Enable/Disable
Enable
Disable
Cancel
OK
(6)
Absence Detection Time
Fri 10:00AM
In
30
min.
Cancel
OK