Brother QL-820NWB Handleiding voor snelle installatie - Pagina 4
Blader online of download pdf Handleiding voor snelle installatie voor {categorie_naam} Brother QL-820NWB. Brother QL-820NWB 10 pagina's. Dk label. dk tape
Ook voor Brother QL-820NWB: Handleiding voor snelle installatie (10 pagina's), Handleiding productveiligheid (11 pagina's), Installatiehandleiding (8 pagina's), Handmatig (2 pagina's)
Pagina afdrukken
3. Loading the DK Roll
1.
Make sure that the Label Printer is turned Off.
Hold the Label Printer by the front, and firmly lift the DK
Roll Compartment Cover to open it.
Remove the Protective Sheet from the Label Output Slot.
IMPORTANT
• Do not throw away the Protective Sheet.
• When the printer is not in use, lift the DK Roll Compartment Cover and remove any DK Rolls from inside
the printer. Then insert the Protective Sheet into the Label Output Slot for the printer to maintain good
printing quality.
2.
After removing the protective material, place the DK Roll
into the Roll Spool Guides.
• Make sure that the Roll Spool Arms are inserted firmly in the
Roll Spool Guides.
• Make sure the Stabilizer (1) slide into the notch of the Label
Printer.
3.
Thread the DK Roll through the Label Printer.
• Align the edge of the DK Roll with the upright edge of the
Label Output Slot.
• Insert the first label into the slot inside the compartment.
• Push the labels through the Label Output Slot until the end
reaches the mark, as shown.
4.
Close the DK Roll Compartment Cover.
When you press the Power (
) Button to turn the Label Printer
On, the end of the DK Roll aligns automatically.
IMPORTANT
• Do not leave the printed labels in the Label Printer. Doing so will cause the labels to jam.
• When not in use, close the DK Roll Compartment Cover to prevent dust and debris from accumulating
in the Label Printer.
NOTE
Press the Cutter Button for two seconds to feed the tape automatically (QL-820NWB only).
4. Connecting the AC Adapter
Connect the AC Power Cord to the Label Printer
and to the AC Adapter. Then, plug the AC Adapter
into a grounded AC electrical outlet.
Protective
Sheet
PA-BU-001 (optional battery unit) can be used.
5. Using the Battery Unit (Rechargeable Li-ion Battery included)
Charging the Battery Unit
NOTE
• Before use, fully charge the Battery Unit.
• To fully charge the Battery Unit, charge for approximately 2.5 hours.
1.
Make sure the Battery Unit is installed in the Label Printer.
2.
Use the AC Adapter and AC Power Cord to connect the Label Printer to an AC power outlet.
Press the Power ( ) Button to turn the Label Printer on if it is not on already.
For QL-810W, the Battery (
1
Unit is fully charged.
NOTE
If the Battery Unit is not fully charged and you use the Label Printer to print, feed, or perform another
operation, the Battery Unit temporarily stops charging, and continues automatically after the operation is
completed.
Stopping Battery Unit Charging
To stop charging the Battery Unit, disconnect the AC Adapter.
Notes on Using the Battery Unit
• Before use, fully charge the Battery Unit. Do not use it until it is fully charged.
• Charge the Battery Unit in environments between 50°F and 95°F (10°C and 35°C), otherwise the Battery Unit will not charge,
and the Battery (
place the Label Printer in environment between 50°F and 95°F (10°C and 35°C) and try charging again.
• If the Label Printer is used to print, feed, or perform another operation when both the battery is installed and the AC Adapter
is connected, the Battery (
Battery Unit Characteristics
• To ensure the highest performance and longest life from the Battery Unit:
• Do not use or store the Battery Unit in a location exposed to extreme high or low temperatures as it may discharge more
quickly. This may happen when using a Battery Unit with a high charge (90% charged or more) in a location exposed to high
temperatures.
• Remove the Battery Unit when storing the Label Printer for a long period of time.
• Store a Battery Unit with less than a 50% charge in a cool dry place out of direct sunlight.
• Recharge the Battery Unit every six months if it is stored for a long period of time.
• If you touch a part of the Label Printer while the Battery Unit is charging, that part of the Label Printer may feel warm. This is
normal, and the Label Printer may be used safely; however, if the Label Printer becomes extremely hot, discontinue use and
allow to cool.
) LED lights in orange during charging, and it turns off when the Battery
) LED will remain lit. If the charging stops because the environment temperature is too low or too high,
) LED may turn off and charging may stop even if the battery is not fully charged.