Indesit LTF 11M132 Gebruiksaanwijzing - Pagina 27

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Indesit LTF 11M132. Indesit LTF 11M132 44 pagina's.

Pagina afdrukken

Rinse aid and refined salt

Only use products which have been specifically designed

for dishwashers.

Do not use table/industrial salt or washing-up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to add

any rinse aid. However, we recommend that you add salt,

especially if you live in an area where the water is hard or

(Follow the instructions given on the packaging).

very hard.

If you do not add salt or rinse aid, the LOW SALT

LOW RINSE AID indicator lights will stay lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water runs off

the surfaces more readily and therefore does not leave streaks

or marks. The rinse aid dispenser should be filled:

• When the LOW RINSE AID indicator light

is illuminated, a reserve supply of rinse aid is still available

for 1-2 cycles;

"D"

1. Open the dispenser

by pressing and pulling up the tab

on the lid;

2. Carefully introduce the rinse aid as far as the maximum

reference notch of the filling space - avoid spilling it. If this

happens, clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results, you

may adjust the quantity of rinse aid used. Switch on and off the

dishwasher using the ON/OFF button. Press the P button three

times. Press the ON/OFF button, the set level appears on the

display

(set to factory level).

Adjust the rinse aid supply level with the P button.

Press the ON/OFF button to save the adjustment setting.

The rinse aid level can be set to ZERO, in such a case the rinse

aid will not be supplied and the low rinse aid indicator light in

case of running out.

A maximum of 4 levels can be set according to the dishwasher

model.

• If there are streaks on the crockery, set to a low number (1-2).

• I n case of drops of water or limescale marks, set to a high

number number (3-4).

Setting the water hardness

Every dishwasher is equipped with a water softener which, by

using refined salt designed especially for this type of appliance,

supplies water without limescale which is then used to wash

the crockery.

This dishwasher offers a setting which helps to reduce pollution

and optimises washing performance in accordance with the

water hardness level in your area. This information can be

obtained from your local water supplier.

Switch on and off the dishwasher using the ON/OFF button. Press

and hold the P button for a few seconds until you hear a beep.

Switch on the dishwasher with the ON/OFF button, the set level

appears on the display

Adjust the water hardness level with the P button,

see water hardness table)

Press the ON/OFF button to save the adjustment setting.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

and

Water Hardness Table

level

on the control panel

For values between 0°f and 10°f, we do not recommend the use of salt.

a setting of 5 may increase cycle duration.

(°dH = hardness measured in German degrees - °f = hardness

measured in French degrees – mmol/l = millimoles per litre)

Measuring out the refined salt

In order to obtain the best possible results from a wash cycle,

make sure that the salt dispenser is never empty.

Refined salt removes limescale from the water, thus avoiding

the formation of deposits on crockery.

The salt dispenser is located in the lower part of the dishwasher

(see Description)

• When the green float

• When the LOW RINSE AID indicator light on the control panel

1. Remove the lower rack and unscrew the cap (anticlockwise).

residues away from the opening; rinse the cap under running

water and then screw it on, the head facing downwards so as to

let the water flow out of the four slots (star-shaped arrangement)

in the lower part of the cap (cap with green float

It is advisable to perform this procedure every time you add

salt to the dispenser.

Make sure the cap is screwed on tightly so that no detergent can

get into the container during the wash cycle (this could damage

the water softener beyond repair).

so that any saline solution which has leaked out of the salt

dispenser is removed.

Only available in selected models.

(water softener set to medium level).

up to a max. of 5 levels.

°dH

°fH

mmol/l

0 - 6

0 - 10

0 - 1

6 - 11

11 - 20

1,1 - 2

3 12 - 17

21 - 30

2,1 - 3

4 17 - 34

31 - 60

3,1 - 6

34 - 50

61 - 90

6,1 - 9

1 wash cycle per day.

and should be filled:

cannot be seen by simply looking at

the cap of the salt dispenser;

is illuminated

;

2. The first time you do this: fill the water

tank right up to its edge.

3. Position the funnel

fill the salt dispenser up to the edge

(approximately 1 kg). It is normal for a

little water to leak out.

4. Remove the funnel* and wipe any salt

When necessary, measure out the salt before a wash cycle

(1-2-3-4-5

Average salt dispenser

capacity duration

months

7 months

5 months

3 months

2 months

2/3 weeks

(see figure)

and