Indesit I5GG Gebruiksaanwijzing - Pagina 4

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Indesit I5GG. Indesit I5GG 16 pagina's.

Pagina afdrukken

Gas connection

T he cooker should be connected to the gas-supply

by a Gas Safe registered installer. During installation

of this product it is essential to fit an approved gas

tap to isolate the supply from the appliance for the

convenience of any subsequent removal or servicing.

Connection of the appliance to the gas mains or liquid

gas must be carried out according to the prescribed

regulation in force, and only after it is ascertained that it

is adaptable to the type of gas to be used. If not, follow

the instructions indicated in the paragraph headed

"Adaptation to different gas types". On some models

the gas supply can be connected on the left or on the

right, as necessary; to change the connection, reverse

the position of the hose holder with that of the cap and

replace the gasket (supplied with the appliance). In the

case of connection to liquid gas, by tank, use pressure

regulators that conform to the regulation in force. The

HOT PARTS

"Caracteristics of the burners and nozzles". When

the cooker is installed between cabinets (recessed),

the gas connection must be effected by an approved

flexible hose with bayonet fitting (BS 669 Current

Edition). The gas inlet for the cookers is a threaded G

1/2 gas female fitting.

Connecting the gas supply

To make the connection, a flexible hose should be

used corresponding to the current gas regulations

which are:

• the hose must never be at any point in its lenght in

contact with the "hot" parts of the cooker;

• the hose must never be longer than 1,5 metre;

• the hose must not be subject to any tension or

torsional stress and it must not have any excessively

narrow curves or bottlenecks;

• the hose must be easy to inspect along its entire

length to check its condition;

• the hose must always be in good condition, never

attempt to repair.

! The installation must comply with gas safety

(installation and use) regulations 1984. In all cases for

the above, by low, a qualified, corgi approved engineer

must be called for installation.

* Only available in certain models

gas supply must be

connected to the left of

the appliance. Be sure

that the hose does not

pass through the rear of

the cooker touching hot

parts.

! Make sure the supply

pressure conforms

with the values shown

in the table entitled

Electrial connection

Power supply voltage and frequency: 230-240V a.c.

50/60 Hz.

! The supply cable must be positioned so that it never

reaches at any point a temperature 50°C higher than

the room temperature. The cable must be routed away

from the rear vents. Should you require it, you may

use a longer cable, however, you must ensure that the

cable supplied with the appliance is replaced by one

of the same specifications in accordance with current

standards and legislation.

Your appliance is supplied with a 13 amp fused

plug that can be plugged into a 13 amp socket for

immediate use. Before using the appliance please read

the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used, and

the fuse cover re-fitted. If the fuse cover is lost, the

plug must not be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking

or the colour that is embossed in words on the base of

the plug. Replacements can be obtained directly from

your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to remove it to add a cable

extension or to re-route the mains cable through

partitions, units etc., please ensure that either:

• the plug is replaced by a fused 13 amp re-wireable

plug bearing the BSI mark of approval.

or:

• the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with

BS 5733) which is accessible without moving the

appliance.

! For appliances with a rating greater than 13 amp (eg:

electric hob, double ovens and freestanding electric

cookers etc.) the mains cable must be wired into a

cooker output point with a rating of 45 amp. In this

case the cable is not supplied.