Indesit IS5G1KMW/U Handmatig - Pagina 8

Blader online of download pdf Handmatig voor {categorie_naam} Indesit IS5G1KMW/U. Indesit IS5G1KMW/U 17 pagina's.

Pagina afdrukken

INSTALLATION TIPS

! After adjusting the appliance so it may be used with a

different type of gas, replace the old rating label with a

new one which corresponds to the new type of gas (these

labels are available from Authorised Technical Assistance

Centres).

! Should the gas pressure used be different (or vary

slightly) from the recommended pressure, a suitable

pressure regulator must be fitted to the inlet hose in

accordance with current standards EN 88-1 and EN

88-2 relating to "regulators for channelled gas".

Adapting the oven

Replacing the oven burner nozzle:

1. Remove the oven compartment.

2. Slide out the protection

panel A

( see diagram ).

3. Remove the oven burner

after unscrewing the screws V

( see figure ).

The whole operation will be

made easier if the oven door

is removed.

4. Unscrew the nozzle using a

special nozzle socket spanner

( see figure ) or with a 7 mm

socket spanner, and replace it

with a new nozzle that is

suited to the new type of gas

( see Burner and nozzle

specifications table ).

Adjusting the gas oven burner's minimum setting:

1. Light the burner ( see Start-up and Use ).

2. Turn the knob to the minimum position (MIN) after

it has been in the maximum position (MAX) for

approximately 10 minutes.

3. Remove the knob.

4. Tighten or loosen the adjustment screws on the

outside of the thermostat pin ( see figure ) until the

flame is small but steady.

! If the appliance is connected to liquid gas, the

bypass screw must be adjusted to minimum.

5. Turn the knob from the MAX position to the MIN

position quickly or open and shut the oven door,

making sure that the burner is not extinguished.

Adapting the grill

Replacing the grill burner nozzle:

1. Remove the oven burner

after loosening screw V ( see

figure ).

WARNING : This operation must be perfomed

by a qualified technician

! Be careful of the spark plug wires and the

thermocouple tubes.

! The oven and grill burners do not require primary

air adjustment.

! After adjusting the appliance so it may be used

with a different type of gas, replace the old rating

label with a new one that corresponds to the new

type of gas (these labels are available from

Authorised Technical Assistance Centres).

! Should the gas pressure used be different (or vary

slightly) from the recommended pressure, a suitable

pressure regulator must be fitted to the inlet hose in

accordance with current national regulations relating

to "regulators for channelled gas".

Electrial connection

Power supply voltage and frequency: 230-240V a.c.

50/60 Hz.

! The supply cable must be positioned so that it never

reaches at any point a temperature 50°C higher than

the room temperature. The cable must be routed away

from the rear vents. Should you require it, you may

use a longer cable, however, you must ensure that the

cable supplied with the appliance is replaced by one

of the same specifications in accordance with current

standards and legislation.

Your appliance is supplied with a 13 amp fused

plug that can be plugged into a 13 amp socket for

immediate use. Before using the appliance please read

the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used, and

the fuse cover re-fitted. If the fuse cover is lost, the

plug must not be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking

or the colour that is embossed in words on the base of

the plug. Replacements can be obtained directly from

your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to remove it to add a cable

extension or to re-route the mains cable through

partitions, units etc., please ensure that either:

• the plug is replaced by a fused 13 amp re-wireable

plug bearing the BSI mark of approval.

2. Unscrew the grill burner

nozzle using a special nozzle

socket spanner ( see figure ) or

preferably with a 7 mm socket

spanner, and replace it with a

new nozzle that is suited to the

new type of gas ( see Burner

and nozzle specifications table