Indesit WD 84 T Instructie - Pagina 6

Blader online of download pdf Instructie voor {categorie_naam} Indesit WD 84 T. Indesit WD 84 T 18 pagina's.

Pagina afdrukken

Here I'm in command

Making the right choice is important. And it's easy.

Programme selector knob

Use this knob to select the wash

programme.

Turn this knob clockwise only.

To select a programme, you

should turn the knob so that the

symbol/number of the desired

programme is in line with the

pointer on the knob.

Now press on/off button H

(position I), pilot lamp I will start

flashing.

After 5", the setting will be

accepted, pilot lamp I will stop

flashing (staying lit) and the wash

cycle will begin.

Should you wish to interrupt the

programme in progress or set a

new one, select one of the

symbols (Stop/Reset) and wait

5" : when the cancellation has

been accepted, pilot lamp I

flashes, and you can then turn the

appliance off.

After the wash cycle has been set

and accepted by the washer-

dryer, turning the knob will have

no effect (except for when it is on

position

Stop/Reset).

Temperature control knob

It is used to set the wash tempe-

rature in the recommended

programme table on pag. 4. It also

allows you to reduce the tempe-

rature recommended for the

selected programme, and even

to set a cold wash cycle ( ).

Drying cycle knob

Use this knob to select the

desired dr ying cycle. Two

options are available:

A - Based on time:

From 40 minutes to 150.

B - Based on the damp level of

the dry clothes:

Iron

:slightly damp clothes,

easy to iron.

Wardrobe

: dry clothes to

put away.

Extra dry

: very dry clothes,

recommended for towelling and

bathrobes.

A cooling stage is foreseen at

the end of the drying cycle.

Detergent dispenser

It is divided into 3 compartments:

1. Detergent for pre-wash;

2. Detergent for the main cycle

wash;

3. Fabric conditioner.

Understanding the control panel

The washer-dryer is equipped

with an extra compartment 4

(provided as an accessory) for

the bleach, to be inserted in

compartment 1.

Slow spin

Use this button to reduce the

spinning speed from 800 to 400

rpm for the cotton and linen

programmes and from 700 to

400 rpm for the synthetic

fabrics programmes.

Rapid wash

This button reduces the length

of the wash programme by

about 30%. It cannot be used

with special programmes (see

page 4) or those for wool and

silk.

Stain removal (see page 8)

Thanks to this command, the

washer-dryer will carry out a

more intensive wash that

optimises the effectiveness of the

liquid additives, thus allowing

more resistant stains to be

removed. When you press the

stain removal button, you cannot

activate the pre-wash.

On-off

When button H is pressed, the

washer-dryer is switched on,

when it is not the machine is

switched off.

Turning the appliance off

does not cancel the selected

programme.

On-off lamp / door locked

Lamp I flashes slowly when the

appliance is switched on and

awaiting instructions and at the

end of a cycle, indicating that the

door can be opened. It flashes

quickly when the door should

not be opened. A steady light

means the appliance has

accepted

the

selected

programme.

Drying cycle lamp

When this lamp is on, it means

that knob C has been set on a

drying cycle and at the end of the

wash cycle, the appliance will run

the selected tumble drying cycle.

Anti-crease

This function (represented by the

symbol

) interrupts the wash

programme, keeping the washing

soaking in water before draining.

It is only enabled in programmes

for synthetic fabrics, silk and

cur tains. It is very useful,

because it prevents delicate and

synthetic fabrics from creasing

(for example, when you cannot

take the washing out at the end

of the wash cycle but only a few

hours later). The programme can

be completed by turning knob A

one notch. In the case of

synthetic fabrics, should you

prefer draining rather than a spin

cycle, turn knob A until you have

selected the symbol

(Drain).