Indesit THP 752 IX/I NL Gebruiksaanwijzing - Pagina 6

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Indesit THP 752 IX/I NL. Indesit THP 752 IX/I NL 16 pagina's.

Pagina afdrukken

by the circuit-breaker). The supply cable must not come into contact with

surfaces with temperatures higher than 50°C.

! The installer must ensure that the correct electrical connection has been

made and that it is compliant with safety regulations.

Before connecting to the power supply, make sure that:

• the appliance is earthed and the plug is compliant with the law.

• the socket can withstand the maximum power of the appliance, which is

indicated on the data plate.

• the voltage is in the range between the values indicated on the data plate.

• the socket is compatible with the plug of the appliance. If the socket is

incompatible with the plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

! Once the appliance has been installed, the power supply cable and the

electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by authorised technicians

only (see Assistance).

! The manufacturer declines any liability should these safety measures not

be observed.

Gas connection

! This operation must be performed by a qualified technician.

The appliance should be connected to the main gas supply or to a gas

cylinder in compliance with current national regulations. Before carrying out

the connection, make sure the cooker is compatible with the gas supply you

wish to use. If this is not the case, follow the instructions indicated in the

paragraph "Adapting to different types of gas."

When using liquid gas from a cylinder, install a pressure regulator which

complies with current national regulations.

! Check that the pressure of the gas supply is consistent with the values

indicated in Table 1 ("Burner and nozzle specifications"). This will ensure the

safe operation and longevity of your appliance while maintaining efficient

energy consumption.

• The connection of the hob to the

gas pipe network or gas cylinder

must be made by means of a rigid

copper or steel pipe with fittings

complying with local regulations, or

by means of a continuous-surface stainless steel hose complying with local

regulations. Interpose gasket (B) in the elbow connection.The maximum

length of the hose is 2 m.

• FOR BELGIUM ONLY: It is necessary to replace the elbow connection

(A) on the appliance, with the one supplied (if present).

IMPORTANT: if a stainless steel hose is used, it must be installed so as

not to touch any mobile part of the furniture. It must pass through an

area where there are no obstructions and where it is possible to inspect

it on all its length.

• After connection to the gas supply, check for leaks with soapy water. Light

up the burners and turn the knobs from max position

position to check flame stability.

Adapting to different types of gas

! This operation must be performed by a qualified technician.

To adapt the hob to a different type of gas other than default type (indicated

on the rating plate at the base of the hob or on the packaging), the burner

nozzles should be replaced as follows:

1. Remove the hob grids and slide the burners off their seats.

2. Unscrew the nozzles using a socket spanner of the appropriate size, and

replace them with nozzles for the new type of gas (see table 1 "Burner

and nozzle characteristics").

3. Reassemble the parts following the above procedure in the reverse order.

4. Once this procedure is finished, replace the old rating sticker with one

indicating the new type of gas used. Sticker are available from any of our

Service Centres.

Use pressure regulators suitable for the gas pressure indicated in the

Instruction.

• The gas nozzles must be changed by After Sales Service or a qualified

technician.

• Nozzles not supplied with the appliance must be ordered from After Sales

Service.

• Adjust the minimum setting of the taps.

NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas

setting screw must be tightened as far as it will go.

IMPORTANT: should you experience difficulty in turning the burners

knobs, please contact the After Sales Service for the replacement of

the burner tap if found to be faulty.

• Adjusting the burners' primary air

Does not require adjusting.

• Setting the burners to minimum

To ensure that the minimum setting is correctly adjusted, remove the knob

and proceed as follows:

2. Having adjusted the flame to the required low setting, while the burner is

alight, quickly change the position of the knob from minimum to maximum

and vice versa several times, checking that the flame does not go out.

3. Some appliances have a safety device (thermocouple) fitted. If the device

fails to work when the burners are set to the low flame setting, increase

this low flame setting using the adjusting screw.

4. Once the adjustment has been made, replace the seals on the by-passes

using sealing wax or a similar substance.

! If the appliance is connected to liquid gas, the regulation screw must be

fastened as tightly as possible.

! Once this procedure is finished, replace the old rating sticker with one

indicating the new type of gas used. Stickers are available from any of our

Service Centres.

to minimum

1. Adjust the adjustment screw, which is

positioned in or next to the tap pin, until the

flame is small but steady:

• tighten screw to reduce the flame height;

• loosen screw to increase the flame height;

The adjustment must be performed with the

tap in minimum gas setting position.