A-T Controls TRIAG M-3POS-115 Installatie- en onderhoudshandleiding - Pagina 2

Blader online of download pdf Installatie- en onderhoudshandleiding voor {categorie_naam} A-T Controls TRIAG M-3POS-115. A-T Controls TRIAG M-3POS-115 2 pagina's. 3 position control card

Pagina afdrukken

INSTALLATION:

 The TM-3POS-115 control card should be mounted to

a metal bracket to properly dissipate the heat

generated by the solid-state outputs.

 A 1000 Ohm or 5000 Ohm potentiometer is used for

position feedback and must connect to terminals 5, 6

& 7. The wiper will connect to terminal 6. The other

two leads connect to terminal 5 and 7 so when the

actuator is rotating CCW, the resistance or voltage is

increasing between terminals 5 & 6.

 The motor and capacitor connect to terminals 8, 9 &

10. The neutral from the motor connects to terminal 9

and the lead that drives the motor CCW to terminal 8

and the lead that drive the motor CW to terminal 10.

 The incoming 115VAC power is connected to

terminals 1 & 2, with LINE on terminal 1 and

NEUTRAL on terminal 2.

 A ground should be attached to a grounding lug

inside actuator housing.

 The 115VAC input control signals connect to terminal

3 & 4. Each input should be powered through it's own

individual switch or relay contacts.

OPERATION:

The TM-3POS-115 control card can be operated to any

of three different positions by providing 115VAC to input

terminals 3 and 4.in two different positioning modes.

IN 2 (#4)

IN 1 (#3)

0 V

115 V

0 V

115 V

A-T Controls product, when properly selected, is designed to perform its intended function safely during its useful life. However, the purchaser or user of A-T Controls products

should be aware that A-T Controls products might be used in numerous applications under a wide variety of industrial service conditions. Although A-T Controls can provide

general guidelines, it cannot provide specific data and warnings for all possible applications. The purchaser / user must therefore assume the ultimate responsibility for the

proper sizing and selection, installation, operation, and maintenance of A-T Controls products. The user should read and understand the installation operation maintenance

(IOM) instructions included with the product and train its employees and contractors in the safe use of A-T Controls products in connection with the specific application.

While the information and specifications contained in this literature are believed to be accurate, they are supplied for informative purposes only. Because A-T Controls is

continually improving and upgrading its product design, the specifications, dimensions and information contained in this literature are subject to change without notice. Should

any question arise concerning these specifications, the purchaser/user should contact A-T Controls.

For product specifications go to

http://download.a-tcontrols.com/

A-T Controls, Inc. • 9955 International Boulevard, Cincinnati, OH 45246 • Phone: (513) 530-5175 • Fax: (513) 247-5462 •

www.atcontrols.com



POSITION

DEFAULT

MID

CCW

MID

Installation & Maintenance Manual

CALIBRATION:

 Set jumper JP1 to the S (Set) position and supply

power to terminals 1 and 2.

 Move to middle position using [CW] or [CCW]

buttons. Adjust the potentiometer to its mid-range.

This is indicated when the voltage between terminal 5

& 6 is approximately 2.5VDC, or somewhere between

2.25VDC and 2.75VDC. Tighten the potentiometer

gear and cam shaft gear set screws.

Press [SET 1 + 2] button to program this position into

memory as the position to move to when Input 1 and

Input 2 are supplied 115V.

 Move actuator to clockwise position using [CW] or

[CCW] buttons. Press [SET 1] button to program this

position into memory. This will be the position the

actuator moves to when Input 1 is supplied 115V.

 Move actuator to counter-clockwise position using

[CW] or [CCW] buttons. Press [SET 2] button to

program this position into memory. This will be the

position the actuator moves to when Input 2 is

supplied 115V.

 Move the jumper JP1 from the S (SET) position to

R (RUN) position. The actuator can now be tested

with the inputs to terminal 3 & 4.

NOTE: The actuator can be programmed to any of the

three positions for any of the input logic. Just move the

actuator to the desired position, and press the button

corresponding to the desired input functionality.

TM-3POS-115

3 Position Control Card

www.atcontrols.com

IOM08107 REVISION 02

06/19/20