Aqua Creek Products PRO POOL-AT F-046QAB-AT Handleiding voor installatie en gebruik - Pagina 4

Blader online of download pdf Handleiding voor installatie en gebruik voor {categorie_naam} Aqua Creek Products PRO POOL-AT F-046QAB-AT. Aqua Creek Products PRO POOL-AT F-046QAB-AT 7 pagina's. Quick-attach anchor

Pagina afdrukken

4 – POINT PRE-SET ANCHOR INSTALLATION

NOTE: THE 4-POINT PRESET ANCHOR CAN BE INSTALLED IN EITHER A

NEW POOL DECK OR AN EXISTING DECK. BEFORE INSTALLING MAKE

SURE THE WATER-D R A F T I S 1 2 " O R L E S S ( D E C K T O WA T E R L I N E ) .

INSTALL THE LIFT AT A LOCATION WITH 42" T O 4 8 " O F D E P T H .

RETRO-FIT INSTALLATION / EXISTING DECK APPLICATION

TOOLS REQUIRED:

MARKING PEN/PENCIL

1-1/4" C O R E D R I L L B I T

CORE DRILL

HAMMER

1. Locate the anchor jig and the FOUR (4) anchor bolts. FIGURE 1

2. Using the anchor jig plate smaller holes as a template, mark the FOUR

(4) hole locations on the deck. The front anchor must be no more than

14 inches [356mm] from the pool wall. FIGURE 3. Make sure to keep

the two rear anchor holes parallel to the pool wall.

3. Rem o v e t h e 1 " h e x n u t s f r o m t h e a n c h o r b o l t s . C o r e D r i l l a 1 -1 / 4 "

[32mm] diameter hole at the FOUR (4) locations marked from step 1.

D r i l l t o a d e p t h o f 4 " t o 5 " [ 1 0 c m t o 1 3 c m ] .

4. Remove the core from the hole with a chisel and hammer if necessary.

Clean out all four holes completely.

5. Fill each hole approximately ½ full with high strength anchor adhesive.*

6. Connect at least one anchor bolt to an existing bonding grid or bonded

metal fitting per local codes. Use 8AWG solid-copper wire.

7. Install the FOUR (4) anchor bolts into the epoxy filled holes. Make sure

that the top of the bolts will be flush with the top of the pool deck.

( N O T E : T o m a k e p o s i t i o n i n g o f t h e a n c h o r s e a s i e r t h e ½ " b o l t s m a y b e

temporarily installed in the anchors to give you something to hold onto.)

8. Let the adhesive cure a s p e r t h e m a n u f a c t u r e r ' s i n s t r u c t i o n s before

installing the PRO POOL-AT

* Use HILTI HIT HY-150 or SIMPSON ET22 StrongTie anchor adhesive

or equivalent.

NEW CONSTRUCTION: ANCHOR INSTALLATION

When the lift is installed on a new deck, the slab sh o u l d b e a m i n i m u m o f 6 " [ 1 5 cm] thick at the

l i f t l o c a t i o n , a n d s h o u l d b e r e i n f o r c e d w i t h # 4 r e i n f o r c i n g b a r a t 1 0 " [ 2 5 . 4 c m ] o n c e n t e r i n e a c h

direction. The total pad area should be 3 feet [92cm] wide (from the edge of the pool back) by 3

feet [92cm] long.

1. Locate the preset anchor jig assembly and the four (4) anchor bolts. Mount the anchor

bolts to the jig plate as shown in FIGURE 2.

2. Bond the jig plate using the attached bronze bonding lug. Check local electrical codes

for anchor bonding. In most cases the jig-plate will be bonded with 8AWG solid-

copper wire (see FIGURE 3).

3. Locate the jig assembly at the desired pool location. The front anchor (centerline)

must be 1 4 " to 19" [35.6cm to 48.3cm] from the pool wall as shown in FIGURE 3.

Make sure to keep the front two anchor holes parallel to the pool wall.

4. Make sure the anchor assembly is plumb and level – secure the anchors, and then

pour the deck.

LEVEL

HIGH STRENGTH ANCHOR ADHESIVE

TAPE MEASURE

CHISEL

lift.

FIGURE 1

(ANCHOR BOLT,

HEX NUTS

REMOVED)