Allied Telesis AT-TQ4400e Snelle installatiehandleiding - Pagina 2

Blader online of download pdf Snelle installatiehandleiding voor {categorie_naam} Allied Telesis AT-TQ4400e. Allied Telesis AT-TQ4400e 2 pagina's. Outdoor wireless access point

Pagina afdrukken

Attaching the Antennas to the Access Point

To attach the antennas the access point, perform the following procedure:

Screw a 5GHz antenna into a 5GHz antenna connector. Repeat this step for the

second 5GHz antenna.

Screw a 2.4GHz antenna into a 2.4GHz antenna connector. Repeat this step for the

second 2.4GHz antenna.

Starting the Initial Management Session

This section contains an abbreviated version of the procedure for starting the initial

management session. For complete instructions, refer to the AT-TQ4400e installation

Guide or AT-TQ Wireless Access Point Series User's Guide.

The wireless access point has a DHCP client. The default setting for the client is enabled.

When you connect the access point to a PoE switch for the first time, the access point

queries the subnet on the LAN port for a DHCP server. If a DHCP server responds to its

query, the access point uses the IP address the server assigns to it. If there is no DHCP

server, it uses the default IP address 192.168.1.230.

To start the initial management session, perform the following procedure:

Start the web browser on your management workstation.

Enter the IP address of the access point in the URL field of the web browser. The

address is one of the following:

If your network does not have a DHCP server, enter the default address



192.168.1.230.



If your network has a DHCP server, enter the IP address the DHCP server

assigned to the access point.

The access point displays the logon prompt.

Enter "manager" for the username and "friend" for the password. The username and

password are case-sensitive.

Setting the Country Setting

For instructions on setting the country setting, refer to the AT-TQ4400e installation Guide or

AT-TQ Wireless Access Point Series User's Guide.

Note

The non-US model of this product has a country code setting that must be set during

the initial management session of the unit. The setting ensures that the unit operates

in compliance with the laws and regulations of your country or region.

The country code for the US model is preset and cannot be changed. Per FCC

regulations, the country code setting for all WiFi products marketed in the US must be

fixed to US operational channels only.

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to which the



receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.



FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna

or transmitter.

The transmission in the band from 5600-5650MHz is disabled by the software installed on

the device. You cannot change this setting. This device meets all the other requirements

specified in Part 15E, Section 15.407 of the FCC Rules.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance

34cm between the radiator & your body.

Industry Canada Statement

This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may cause

undesired operation.

Ce dispositif est conforme à la norme CNR-247 d'Industrie Canada applicable aux

appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions

suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce

dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de

provoquer un fonctionnement indésirable.

Caution:

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the

potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and

5470-5725 MHz shall comply with the e.i.r.p. limit; and

(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall

comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as

appropriate.

(iv) Users should also be advised that high-power radars are allocated as primary users

(i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars

could cause interference and/or damage to LE-LAN devices.

Avertissement:

Le guide d'utilisation des dispositifs pour réseaux locaux doit inclure des instructions

précises sur les restrictions susmentionnées, notamment:

(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement

pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux

systèmes de satellites mobiles utilisant les mêmes canaux;

(ii) le gain maximal d'antenne permis pour les dispositifs utilisant les bandes 5 250-5 350

MHz et 5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.;

(iii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande 5 725-5 825

MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l'exploitation point à point et non

point à point, selon le cas.

(iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de

haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les

bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du

brouillage et/ou des dommages aux dispositifs LAN-EL.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance

36cm between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour

un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un

minimum de 36cm de distance entre la source de rayonnement et votre corps.

European Union Restriction of the Use of Certain Hazardous

Substances

(RoHS) in Electrical and Electronic Equipment

This Allied Telesis RoHS-compliant product conforms to the European Union Restriction of

the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment.

Allied Telesis ensures RoHS conformance by requiring supplier Declarations of Conformity,

monitoring incoming materials, and maintaining manufacturing process controls.

Europe - EU Declaration of Conformity

This device complies with Directive 2014/53/EU issued by the Commission of the

European Community. For more information, refer to the AT-TQ4400e Installation Guide.

Note: Contact Allied Telesis for the EU conformity statement. To contact Allied Telesis, visit

our web site at www.alliedtelesis.com.

Product Specifications

For product specifications, refer to the AT-TQ4400e Installation Guide.

No part of this publication may be reproduced without prior written permission from Allied

Telesis, Inc.

Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All

other product names, company names, logos or other designations mentioned herein are

trademarks or registered trademarks of their respective owners.

Allied Telesis, Inc. reserves the right to make changes in specifications and other

information contained in this document without prior written notice. The information

provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be

liable for any incidental, special, indirect, or consequential damages whatsoever, including

but not limited to lost profits, arising out of or related to this manual or the information

contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have

known, the possibility of such damages.