Dell DX6000 Aan de slag handleiding - Pagina 11

Blader online of download pdf Aan de slag handleiding voor {categorie_naam} Dell DX6000. Dell DX6000 28 pagina's. Rack installation instructions — static rails
Ook voor Dell DX6000: Aanvullende handleiding (4 pagina's), Instructies voor installatie van hardware (2 pagina's), Gebruikershandleiding (46 pagina's), Installatie- en configuratiehandleiding (43 pagina's), Installatie- en configuratiehandleiding (35 pagina's), Kennisgeving (28 pagina's), Kennisgeving (20 pagina's), Overzicht (19 pagina's), Configuratiehandleiding (9 pagina's), Configuratiehandleiding (9 pagina's), Release Release (8 pagina's), Referentiehandleiding (12 pagina's), Configuratiehandleiding (7 pagina's), Release Release (6 pagina's), Release Release (5 pagina's), Release-opmerkingen (5 pagina's), Installatie-instructies (2 pagina's), Installatie-instructies (2 pagina's)

Pagina afdrukken

2.3.1. Setting Up NTP for Time Synchronization

DX Storage clusters are capable of synchronizing their nodes' clocks internally. However, Dell

strongly recommends you use one or more trusted network time protocol (NTP) servers whenever

they are available. This assures that a cluster's clock is in sync with the clocks of the client

machines. If you boot DX Storage from a CSN, the CSN provides NTP services for all DX Storage

nodes and no further configuration is required.

If one or more trusted NTP servers are available, configure DX Storage to use them by setting the

timeSource parameter in the node or cluster configuration files. The value of the timeSource

parameter is a list of one or more NTP servers separated by spaces. An example follows:

timeSource = 10.20.40.21 10.20.50.31

If your DX Storage nodes are able to resolve host names, you can use

recommends you use pool servers that are close to your servers' time zone as discussed

ntp.org help

page. (To view the page in a language other than English, start with

click the "how do I use?" link.)

The following example shows how to use United States-based NTP servers:

timeSource = 0.us.pool.ntp.org 1.us.pool.ntp.org 2.us.pool.ntp.org

Note

NTP version 3 has design limitation that causes time to wrap in the year 2036. If a

computer's BIOS clock is set beyond this wrap point, NTP cannot correct the time. Make

sure that all BIOS clocks are set to a date prior to 2036 before booting DX Storage.

Alternatively, you can use NTP version 4.

2.3.2. Setting Up DNS for Name Resolution

The domain name service (DNS) is used to resolve host names into IP addresses. While DNS is

not required for DX Storage nodes to communicate with each other, DNS can be very useful for

client applications to reach the cluster. If you use named objects, DNS is one method you can use to

enable access to objects over the Internet.

Although client applications can initiate first contact with any node in the DX Storage cluster – even

choosing to access the same node every time - Dell recommends that the node of first contact be

evenly distributed around the cluster.

Basic options follow:

• Define multiple DNS entries ("A" or "CNAME" records) that each specify the IP address of the

same DX Storage node of first contact.

• Use multiple IP addresses for a DNS entry to create a DNS round-robin which provides client

request balancing.

Consult your DNS software documentation for guidance on using "A" records and "CNAME" (alias)

records.

The following example shows the entries for three node IP addresses tied to one name. This is the

configuration file format of the widely used ISC Bind Daemon.

DX Storage

IN A

192.168.1.102

IN A

192.168.1.101

NTP pool

servers. Dell

on the

www.ntp.org

and

Version 5.0

December 2010