Allied Telesis AT-PWR10 Installatiehandleiding - Pagina 2

Blader online of download pdf Installatiehandleiding voor {categorie_naam} Allied Telesis AT-PWR10. Allied Telesis AT-PWR10 2 pagina's. Redundant power supply (ac)

Pagina afdrukken
Allied Telesis AT-PWR10 Installatiehandleiding
3.
Place the locking levers on the new AT-PWR10 power supply in the released
position.
A T- P
W R 10
A C
P
O
F
A
W
E
U
L
R
T
W A R
N IN G
BE FO
R E
EJ EC
TI N G
LO O
,
SE N
TH U
M B SC
R EW
4.
Slide the new AT-PWR10 power supply into the power supply slot until it makes
contact with the backplane of the chassis. Be sure that the labeling on the
power supply is right-side up. Also be sure to align the green board on the
power supply with the slots in the chassis. Once the power supply makes
contact with its connector on the backplane, press firmly to fully seat the power
supply on the power connector.
1
AT -8
2
41 1
AT -P
TX
W R 10
AT -8
AC
TX
P
O
F
W
A
E
U
R
L
T
AT -P
W R 10
AC
P
F
O
A
W
U
E
R
L
T
W A R
N IN G
BE FO
RE
EJ EC
TI NG
LO O
,
SE N
TH UM
BS CR
EW
LN K
AC T
10
EJE
100
CT
LN K
10
EJE
CT
Note
If you are unable to slide the power supply completely into the slot, you may
have purchased the wrong type of power supply for the chassis. An AC
powered chassis has two AC power sockets on the back panel.
5.
Move the locking levers on the AT-PWR10 unit into the locked position and
tighten the captive screw to secure the power supply in the chassis.
Note
Always use the locking levers and the installation screw to secure the power
supply to the switch. Leaving the power supply partially seated may cause the
system to halt and subsequently crash.
6.
Connect an AC power cord to the POWER B power connector on the back panel
on the chassis and secure the cord by lowering the securing bracket.
3
41 1
AT -8
41 1
TX
AC T
100
LN K
AC T
10
EJE
CT
100
7.
Connect the other end of the power cord to an appropriate power source.
8.
Check the POWER LED on the front of the power supply. It should be steady
green. If the LED remains off, reinstall the unit by repeating this procedure.
4
AT -P
W R 10
A C
AT -P
W R 11
D C
P
O
F
W
A
E
U
R
L
P
T
F
O
A
W
U
E
L
R
T
W A R
N IN G
BE FO
RE
EJ EC
TI NG
LO OS
,
W A R
TH UM
EN
N IN G
BS CR
BE FO
EW
EJ EC
RE
TI NG
LO OS
,
TH UM
EN
BS CR
EW
W A R
N IN G
T h is
u n it
th a n
m ig h
o n e
t h a v
re d u
p o w
e m o
c e th
e r c o
re
s h o c
e ri s
rd . T
k , d is
k o f
o
p o w
e le c
c o n n
e r c o
tr ic
e c t a
s e rv
rd s b
ll
ic in g
e fo re
u n it .
P W R
B
F A N
A
P W R
A
W A R
N IN G
T h is
u n it
th a n
m ig h
o n e
t h a v
re d u
p o w
e m o
c e th
e r c o
re
s h o c
e ri s
rd . T
k , d is
k o f
o
p o w
e le c
c o n n
e r c o
tr ic
e c t a
s e rv
rd s b
ll
ic in g
e fo re
u n it .
P W R
B
F A N
A
P W R
A
9.
Slide the power supply cover back into the chassis and secure the cover by
tightening the two captive screws.
1
A T- 84
11
TX
LN K
AC T
10
EJE
CT
100
Technical Specifications
Power Specifications:
Maximum Operating Temperature:
Maximum Storage Temperature:
Operating and Storage Altitude:
Relative Humidity Operating
and Storage:
Electrical Safety and Emission Statement
Standards: This product meets the following standards when installed in compliant host equipment.
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to
Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with this instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right to
operate this equipment.
Industry Canada
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du
Canada.
Emission
FCC Class A, EN55022 Class A, EN61000-3-2, EN61000-3-3, VCCI Class A, C-TICK
WARNING:
In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.
Immunity
EN55024
Electrical Safety UL60950 (UL/cUL), EN60950 (TUV)
Copyright  2003 Allied Telesyn, Inc. All rights reserved.
No part of this publication may be reproduced without prior written permission from Allied Telesyn Inc.
5
1
A T- 84
11
TX
LN K
AC T
10
EJE
100
CT
100-240V AC, 3A maximum, 50/60 Hz
0° C to 40° C (32° F to 104° F)
-20° C to 80° C (-4° F to 176° F)
Up to 3,048 meters (10,000 feet)
5% to 80% (non-condensing)
6