EarthWay EV-N-SPRED C24HDS Montage- en bedieningshandleiding - Pagina 8
Blader online of download pdf Montage- en bedieningshandleiding voor {categorie_naam} EarthWay EV-N-SPRED C24HDS. EarthWay EV-N-SPRED C24HDS 10 pagina's. Broadcast spreader
Ook voor EarthWay EV-N-SPRED C24HDS: Montage- en bedieningshandleiding (9 pagina's)
Pagina afdrukken
ADJUSTING THE EV-N-SPRED
1. Next, using the (7) low baking tins position, them in a straight line on
2-foot centers across the spread width as shown at the right.
Adjust the left or right variable throwing ports to EVEN THE SPREAD
pattern. TIP: For large/heavy materials, close the LEFT SIDE (LINES)
port slightly before you start your EV-N-SPRED
materials, open the LEFT SIDE (LINES) port fully and close the RIGHT
SIDE (DOTS) port slightly before you start your EV-N-SPRED
With BOTH ports closed, the spread is only from the center port, and
will give you a 3-4ft spread width in the center of the spreader - great for
medians.
Begin pushing the spreader several feet before the line of tins and at
normal walking speed. Walk along the Center Line, and OPEN the
Lever to the STOP 3-4 paces before the line of tins and continue walking
past the tins 1 or 2 paces and CLOSE the Lever and STOP.
Visually evaluate the material in the baking tins to determine if your
spread pattern is balanced - having the same amount of material in each
baking tin.
Empty each tin back into the spreader, adjust the ports and RETEST
until you are satisfied that the coverage is balanced.
Spread width
Length needed for
in feet
7
8
9
10
11
12
13
ESTABLISH THE SETTING RATE
2. Remove the material from the hopper, and mark the distance that you
need to travel with the spreader to attain the designated coverage area
- i.e. 1,000 square feet using the spread width you determined earlier.
Above is a chart to help determine the distance needed for 1,000 square
foot calculation.
Mark the START and END POINTS on the surface required for the test.
Weigh a small amount (10-20lbs/4-9kg) of the material, and add that into
to the spreader. Using the Setting Matrix included with the spreader,
estimate a setting rate based on material manufacturers recommendations
and adjust the STOP on the Gauge to that position.
Now to test, start walking 1-2 paces before the START LINE and OPEN
the Lever to the stop and then CLOSE when you cross the END POINT
LINE.
Pour the remaining material from the spreader and weigh to calculate the
amount applied over the area. Adjust the Setting Rate to a higher number
if you need to increase the application rate, or to a lower number if you
applied too much in the test.
You may need to repeat this process to acquire the exact rate.
The EV-N-SPRED
Dual Port PRO Adjustable Shut-Off System ensures
®
that EarthWay
Professional spreaders evenly spread all types of fertilizers, seed, ice melt, or other granular
®
products, and is only available from EarthWay
DUAL PORT SHUT-OFF SYSTEM
®
®
Spread width
1,000 Sq Ft
in feet
142' 11"
14
125'
15
111' 1"
16
100'
17
90' 11"
18
83' 4"
19
76' 11"
20
.
®
test. For small/light
test.
®
Length needed for
1,000 Sq Ft
71' 5"
66' 8"
62' 6"
58' 10"
55' 7"
52' 7"
50'
2'
2'
2'
2'
END
COVERAGE AREA
i.e. 1,000 SQ FT
START
2'
2'