Dialight ProSite Floodlight UL 1598 Installatie- en bedieningsinstructies - Pagina 6

Blader online of download pdf Installatie- en bedieningsinstructies voor {categorie_naam} Dialight ProSite Floodlight UL 1598. Dialight ProSite Floodlight UL 1598 10 pagina's.

Pagina afdrukken

Variable Voltage Control

An analog 0-10 V active dimmer may be

connected to the two wires to control the

light output of the fixture. Multiple lights may

be connected to the same dimmer, as long

as the maximum current rating of the dimmer

is not exceeded.

See table for current sinking capabilities of

the

dimmer.

Light

output

approximately linearly with control voltage,

with 10 V corresponding to 100% light output.

Part Number

F1U***********

F2U****(F/H)******

F2U****(L/N)******

NOTE: Simply shorting the two wires together

will cause the light to shut off.

WARNING: Improper installation, operation,

or maintenance of this luminaire may result in

the invalidation of the warranty, certificate,

or declaration of conformity.

DALI Control (If Applicable)

DALI is used to control/schedule and group

the luminaire. A DALI controller is to be

provided by the installer. The luminaire will not

provide a bus signal. A Bus power supply

should be used to provide a Bus signal

according to the DALI standard.

WARNING: Never connect the DALI wires to

the Hot/Live or Neutral supply wires.

WARNING: Do not connect the DALI wires to

the dimming wires.

For luminaires containing one power supply

[F1U*********** & F2U****(F/H)******], only one

DALI address will be assigned by the DALI

controller.

For luminaires containing two power supplies

[F2U****(L/N)******], two DALI addresses will

be assigned by the DALI controller.

NOTE: The DALI circuit in two power supply

luminaires are already internally wired as a

daisy chain to allow for commissioning and

discovery. The

Bus wire

connected to the DALI terminal block

positions in the wiring compartment.

9100FLM000900 REV E

Page 6 of 10

ProSite Floodlight for UL 1598/1598A

NOTE: Make sure luminaires containing two

power supplies are grouped and scheduled

will

vary

together for the luminaire to function in the

correct manner.

WARNING: Improper installation, operation,

or maintenance of this luminaire may result in

Current

the invalidation of the warranty, certificate,

0.5 mA

or declaration of conformity.

0.5 mA

1.0 mA

Maintenance / Inspection

This LED luminaire should require a minimum

amount of maintenance. If any unforeseen

repairs are required, please contact Dialight

or its authorized representative.

Within

the

inspection routine the following should be

included:

 Protective hoses should be covering the

connection cables.

 Cable entries must be free of corrosion.

 The lens should be cleaned periodically as

needed to ensure continued photometric

performance. Clean the lens with a damp,

non-abrasive,

sufficient, use mild soap or a liquid cleaner.

 Inspect the luminaire to ensure that it is free

of any obstructions or contamination (i.e.

excessive dust build up). Clean with a non-

abrasive cloth if needed.

 Perform visual mechanical and electrical

inspections

recommend routine checks to be made

on a yearly basis. Frequency of use and

environment should determine this.

It is recommended to follow an Electrical

Preventive

described in NFPA 70B: Recommended

Practice for Electrical Equipment.

Repairs / Overhaul / Modification

The equipment must be operated according

to the intended purpose in a perfect and

undamaged condition.

needs to be

NOTE: Should the luminaire enclosure be

damaged, only a full luminaire replacement

will be permitted. In case of doubt, the

equipment should be returned to Dialight for

inspection/repair.

scope

maintenance

lint

free

cloth.

not

regular

basis.

Maintenance

Program

Dialight, 1501 Route 34 South, Farmingdale, NJ, USA 07727

Tel: +1 732 919 3119 Fax: +1 732 751 5778

Disposal & Recycling

When the apparatus is disposed of, the

respective national regulations on waste

disposal should be observed.

Secondary Retention Cable

Part Number

H6XCAB60

Secondary Retention

Cable, Stainless Steel, 60"

H6XCAB72

Secondary Retention

Cable, Stainless Steel, 72"

1. Read and follow all instructions in the

installation manual provided with the

secondary retention cable.

2. Connect the safety cable to one of the

retention brackets on the luminaire.

3. When using a safety cable for secondary

retention, ensure minimum slack in the

cable installation. The slack should be no

greater than 1 ft. [0.3 m]

NOTE:

Cable

type, size, material, and

attachment method to meet customer

application and to be appropriate with all

local and regional regulations.

F1 Retention Bracket Locations

F1 Retention

Bracket

Description