Aquant FLAT Series Installatie- en onderhoudshandleiding - Pagina 3
Blader online of download pdf Installatie- en onderhoudshandleiding voor {categorie_naam} Aquant FLAT Series. Aquant FLAT Series 10 pagina's.
Pagina afdrukken4. ASSEMBLY:
The floodlamp is supplied with 2.5m of cable. It should be inserted through the conduit body(Fig 4), leaving
approximately 1.5m of cable in order to be able to remove the floodlamp to the border of the swimming pool if
handing or lamp change is required(Fig 1).
Wind the cable in counter-clockwise direction under the screen fastening clamps(Fig 5). Firmly secure the gland
seal nut (Fig 6).
In order to secure the floodlamp to the crosshead mount, ensure that the word "TOP" is located on the upper part.
First, insert the lower clamp of the screen in the crosshead mount.
Then, screw the upper part until the floodlamp is firmly inserted in the crosshead mount(Fig7-8).
5. MAINTENANCE:
To r e m ove the floo d la mp to t h e edge of the swimming p ool ( F ig . 1) Insert a screwdriver through the upper hole of the
ornament and unscrew the spline of the mount until the floodlamp is released.(Fig 7-8).
Pull up on the floodlamp until it is released from the lower groove and can be removed from the seimming pool.
Unscrew all the 8 screws, Open the floodlamp (Fig 5).
Pull on the lamp to separate it from the lamp holder. Connect the new LED plate.
VERY IMPORTANT: To change the lamp, always use the cardboard protector and never touch the new lamp with your bare
hands.
Then, assemble the floodlamp in the opposite order of that described. Make sure that the butt joint and the transparent lens are
iinserted properly in the screen seat.
Align the word "TOP" on the ornament with the word "TOP" on the screen fastening.
Turn the ornament slightly to the right until it is fitted with the screen.
Wind 1..5m of cable in counter-clockwise direction under the screen fastening clamps. (Fig 5)
Atten ti on:
B efore any handling e n s ur e that the r e is N O voltage s upp lied to the floo dlamp .
T h e n ew lamp should h ave the sa m e ch a r a c te ris ti c s as t h at su pp lie d with t h e floo d la mp , (LED lamp).
In orde r to e n s ur e full watertightness, clea n the seat of the floodlamp lens joint or r e pla ce this if any permanent
deformation or notches are visible.
6. START -U P:
Ensure t h at the voltage the lamp re c e iv es is n eve r greater than 12 V.
The floo d lamp sho u ld o n ly operate und erwater w h ile se cu re d to the verti cal walls of the p ool. N ever switc h on the
floo d la mp if it is not un de r water.
7. COLOR LED CONTROL:
To change the color mode just turn the light switch OFF then ON within 1.5 seconds on each color mode until you
select the required color mode. If you require to select a new color after the light mode is set just switch off the light
switch for 2 seconds and the lamp will reset to mode 1.
Mode 1
Mode 2
Color
white
Auto change
8. SAFETY WARNI N GS:
The persons who are i n charge of assembly should have the required qual if icatlons f or t his t ype of work.
If the end cab l e of t his li gh t fitti ng is damaged, it should only be replaced by the manufacturer,
its t echnica l service or by a similar l y qualified person, to avoid any danger.
Avoid making contact w i th t he elec t r i c vo lt age.
Comply w it h t he curren t standards regarding accident preven ti on.
In this regard, t he IEC 364-7-702 s t andards must be observed. WIRING I N BUI L DI NGS.
SPECIAL WI RI NG. SWIMMING POOLS.
Any operation re l ated t o t he maintenance or replacemen t o f parts should be performed w it h
t he flood l amp disconnec t ed from the elec t ric power system.
Do not handle w it h we t f ee t .
The manufacturer is no t responsib l e in any c i rcums t ances for assembly, ins t allation or s t ar t- up o f
any electric componen t s which have been inserted or handled at l ocations other than Its own premises.
Mode 3
Mode 4
Mode 5
Blue
Green
Red
Mode 6
Mode 7
Mode 8
Amber
Purple
Disco