Miller Travel Master SB-10D Gebruikershandleiding - Pagina 7

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Miller Travel Master SB-10D. Miller Travel Master SB-10D 44 pagina's. Automatic welding sidebeam

Pagina afdrukken
3-1.
LOCATION (Figures 2-1 And 3-1)
Select an installation site which provides the following:
1.
Mounting surface capable of supporting weight of
Sidebeam assembly
2.
Adequate space for carriage travel and equip-
ment installation
3.
Correct input power supply
4.
Adequate ventilation and fresh air supply
5.
No flammables
6.
A clean and dry area
7.
Proper airflow around unit
8.
Adequate space for removing wrapper(s) and
components for installation, inspection, mainte-
nance, and repair functions.
Holes are provided in the mounting posts, carriage, and
crossarm for installing equipment.
3-2.
SUPPLIED EQUIPMENT (Figure 3-1)
The following equipment is supplied as standard and re-
quires installation or assembly:
1.
Beam
2.
Beam Mounting Posts
3.
Carriage Control With Mounting Bracket
4.
Crossarm
5.
Carriage
6.
Spool Support Assembly
7.
Carriage Control Motor Assembly
8.
Automatic Weld Control Interconnecting Cords
(see Section 4 - AUTOMATIC WELD CONTROL
CONNECTIONS)
IMPORTANT: Automatic Weld Control is not supplied
as standard with this unit.
3-3.
BEAM INSTALLATION (Figure 3-1)
WARNING:
IMPROPER LIFTING OR IN-
STALLING OF EQUIPMENT can cause per-
sonal injury and equipment damage.
Use equipment of adequate capacity to lift
components.
Use bolts and fasteners of adequate capacity
to assemble and install unit.
FALLING BEAM ASSEMBLY can cause seri-
ous personal injury and equipment damage.
Use 3/4 in. (19.1 mm) diameter SAE grade 5
noncorrosive steel hardware for securing
beam mounting post assemblies to floor.
SECTION 3 – INSTALLATION
1.
2.
3.
4.
5.
3-4.
1.
2.
3.
IMPORTANT: If vertically installing carriage, tip bottom
of carriage slightly upward to make installation easier. If
sliding carriage onto end of beam, remove safety stop,
but be sure to reinstall stop after carriage is installed.
4.
5.
6.
Secure beam mounting post assemblies to floor
(hardware must be customer supplied).
Install beam onto mounting post assemblies us-
ing supplied 1/2-13 x 1-1/4 in. hardware. Tighten
screws, then loosen them 1/4 turn.
Install two supplied 1/2-13 x 1-1/4 in. leveling
screws into underside of each mount bracket.
Adjust leveling screws until beam is level.
Tighten beam mounting screws, securing beam
to mounting post assemblies.
CARRIAGE AND CARRIAGE MOTOR IN-
STALLATION (Figure 3-1)
Loosen securing nut on top side of each front cam
follower (cam followers closest to front face of
carriage).
Rotate the two front cam followers on carriage
out as far as possible away from the two rear cam
followers.
WARNING:
IMPROPER LIFTING OR IN-
STALLING OF EQUIPMENT can cause per-
sonal injury and equipment damage.
Use equipment of adequate capacity to lift
components.
Install carriage onto beam by lowering it vertically
from above the beam, or by sliding it horizontally
onto the beam from either end. (After carriage is
installed, be sure that bearing bar on top side of
beam is located between the front and rear cam
followers on the carriage.).
Install the motor mounting bracket onto the car-
riage as follows:
a. Install motor adjustment screw into threaded
hole in motor mounting bracket (see Figure
3-1). Install screw so that head of screw will
face motor when it is installed.
b. Install lock nut onto end of adjustment screw.
c. Install motor mounting bracket onto underside
of carriage top surface using the supplied
3/8-16 x 7/8 in. button-head socket capscrews.
Install and secure motor into mounting bracket
using the two supplied shoulder bolts. Install mo-
tor with motor cord up and motor spring ring fac-
ing the beam. Be sure that the motor pinion gear
rides in the gear rack on the beam.
Install supplied motor engagement spring from
ring on rear of motor casing to ring on back sur-
face of carriage.
OM-889 Page 3