Diamond Z7GCGL6C0A Handmatig - Pagina 7

Blader online of download pdf Handmatig voor {categorie_naam} Diamond Z7GCGL6C0A. Diamond Z7GCGL6C0A 13 pagina's.
Ook voor Diamond Z7GCGL6C0A: Gebruiksaanwijzing (13 pagina's), Handmatig (13 pagina's)

Pagina afdrukken

5.1.4 GAS PRESSURE REGULATOR

If the gas pressure is higher than that specified or is difficult

to regulate (not stable), install a gas pressure regulator

(accessory code 927225) in an easily accessed position

ahead of the appliance.

The pressure regulator should preferably be fitted horizontally,

to ensure the right outlet pressure:

• "1" connection side gas from mains.

• "2" pressure regulator;

• "3" connection side gas towards the appliance;

The arrow on the regulator (

direction.

AUSTRALIA: the gas pressure regulator supplied with the

appliance must be fitted to the appliance inlet. Adjust the

test point pressure with all hob burners operating at maximum

setting as follow:

- 1.0 KPa for Natural gas

- 2.65 KPa for Propane gas

NB! These models are designed and certified for use with

natural or propane gas.

5.1.5. CHECKING THE PRIMARY AIR SUPPLY

When the primary air supply is correctly adjusted, the flame

does not "float" with burner cold and there is no flareback

with burner hot.

• Undo screw "A" and position aerator "E" at distance "H"

given on the Table B, retighten screw "A" and seal with

paint (fig. 3A).

5.1.6 CONVERSION TO ANOTHER TYPE OF GAS

"Technical data/gas nozzles" Table B gives the type of nozzles

to be used when replacing those installed by the manufacturer

(the number is stamped on the nozzle body).

At the end of the procedure, carry out the following check-list:

C he c k

• b u rn e r n o zzle /s re p la ce m e n t

• co rre ct a d ju stm e n t o f p rim a ry a ir su p p ly to

b u rn e r/s

• p ilo t n o zzle /s re p la ce m e n t

• m in im u m fla m e scre w /s re p la ce m e n t

• co rre ct a d ju stm e n t p ilo t/s if n e ce ssa ry

• co rre ct a d ju stm e n t o f su p p ly p re ssu re

(se e te ch n ica l d a ta /g a s n o zzle s ta b le )

• a p p ly sticke r (su p p lie d )

w ith d a ta o f n e w g a s typ e u se d

) shows the gas flow

5.1.6.1 REPLACING THE MAIN BURNER NOZZLE

(cooktop)

• Unscrew nozzle "C" and replace it with the corresponding

nozzle for the selected gas (Table. B, fig.3B) complying

with that given in the following table.

• The nozzle diameter is given in hundredths of mm on the

nozzle body.

• Fully retighten nozzle "C".

5.1.6.2 REPLACING THE PILOT BURNER NOZZLE

(cooktop)

• Undo screw coupling "H" and replace nozzle "G" with one

suitable for the gas type (Table B, fig.3C).

• The nozzle identification number is given on the nozzle

body.

• Retighten screw coupling "H".

5.1.6.3 REPLACING THE MINIMUM FLAME SCREW

(cooktop)

• Unscrew minimum flame screw "M" from the cock and

replace it with one suitable for the type of gas (screw down

fully) (Table B, fig.2B).

5.1.6.4 REPLACING THE MAIN BURNER NOZZLE

(oven)

• Remove the oven floor.

• Unscrew nozzle "F" (Table B, fig. 3A).

• Remove the nozzle and aerator.

• Replace nozzle "F" with the corresponding nozzle for the

selected gas, according to that given in the table B.

• The nozzle diameter is given in hundredths of mm on the

nozzle body.

• Insert nozzle "F" in aerator "E", then fit the two assembled

components in their position, screwing the nozzle down tightly.

5.1.6.5 REPLACING THE PILOT BURNER NOZZLE

(oven)

• Undo screw coupling "H" and replace nozzle "G" with one

suitable for the gas type (Table B, fig.3D).

• The nozzle diameter is given in hundredths of mm on the

nozzle body.

• Retighten coupling "H".