Diamond GB601W HC Handmatig - Pagina 10

Blader online of download pdf Handmatig voor {categorie_naam} Diamond GB601W HC. Diamond GB601W HC 13 pagina's.

• make sure that the appliance is connected to an efficient earthing system

• make sure that the capacity of the power supply system suits the maximum power value indicated on the rating plate of the

appliance

• the appliance is supplied with a plug, prepare a socket controlled by an omnipolar circuit-breaker (7 in Fig. 4), with a contact-

opening gap of not less than 3 mm, that provides full disconnection under overvoltage category III conditions, sin accordance

with national safety standards currently in force. This switch must be equipped with fuses, with the associated residual current

device positioned in such a way as to be readily accessible. Insert the plug into the socket controlled by the switch (7 in Fig. 4)

• the plug must only be replaced by professionally qualified and authorized personnel, and the new plug must comply with

current national safety standards

• if the appliance comes supplied without a plug and you wish to connect it permanently to the power supply, prepare an omnipolar

circuit-breaker (7 in Fig. 4), with a contact-opening gap of not less than 3 mm, that provides full disconnection under overvoltage

category III conditions, in accordance with national safety standards currently in force. This switch must be equipped with fuses,

with the associated residual current device positioned in such a way as to be readily accessible. This operation must be carried

out by a specialized technician

• make sure that you fully uncoil the power supply cable and check that it is not crushed in any way

• should the supply cable be damaged, it must be replaced by a specialized technician using a special cable available from the

Manufacturer or from the Technical Service Centres

6 START-UP

6.1 CLEANING INTERNAL PARTS

The appliance will have already been cleaned in the factory. However, you are advised to wash the internal parts again before

using the appliance. Make sure that the power supply cable is unplugged before carrying out the above cleaning operation.

See cleaning and sanitizing manual for information regarding cleaning operations.

Use ordinary washing-up liquid or a water and vinegar solution for cleaning operations; after cleaning, rinse thoroughly with cold

water and discard the ice produced during the first 30 minutes after cleaning, together with any ice present in the bin.

It is advisable to avoid using abrasive detergents or powders, since these might damage the finish.

6.2 START-UP

Once the appliance has been correctly connected to the electricity mains, water mains and water drain system, it can be started

up as follows:

a) turn on the water supply tap (8 in Fig. 4)

b) insert the plug (if any) in the socket and switch on the power supply by means of the relative switch fitted during the installation

phase (7 in Fig. 4)

Switch on appliance by pressing the luminous switch (13 in Fig. 3).

For appliances that are connected permanently to the electricity mains, turn on by means of the switch on the outside of the

appliance, fitted during the installation phase.

6.3 CLEANING THE STEEL PARTS

The appliance was cleaned initially in the factory. For subsequent cleaning operations on the steel parts of the machine, comply with the

instructions below:

Do not allow saline solutions to dry or pool on the external steel components of the machine, as this may lead to corrosion.

Avoid contact with ferrous material (scourers, forks, ladles, scrapers, etc.) to prevent corrosion, contamination from ferrous particles

circulating in the receptacle.

Carefully clean the stainless steel parts with a damp cloth, water and soap or common, non-abrasive chlorine or ammonia based

detergents.

7 MAIN CAUSES OF OPERATING FAILURE

Should the appliance fail to produce ice, before calling on the Authorized Technical Service Centre, first check carefully that:

• the water supply tap (8 in Fig. 4), fitted during the installation phase, has been turned on

• electric power is reaching the appliance; the plug (if any) is properly inserted in the socket, the switch (7 in Fig. 4) is in the "ON"

position, and the push button (13 in Fig. 3) is lighted up

Furthermore:

• if there is excessive noise, make sure that the appliance is not touching furniture or sheet metal which can give rise to noise or

vibrations

• should any trace of water appear, check the drain hole of the container to ensure that it is not clogged, that the water fill and

drain pipes are correctly connected and are not throttled or damaged

• make sure that the temperature of the air or water does not exceed the installation limit values (see paragraph 5.2)

• make sure that the water inlet filter is not clogged (see paragraph 9.1)