Panasonic CT-20SL14 - 20" CRT TV Handmatig - Pagina 12

Blader online of download pdf Handmatig voor {categorie_naam} Panasonic CT-20SL14 - 20" CRT TV. Panasonic CT-20SL14 - 20" CRT TV 28 pagina's.

Pagina afdrukken

REMOTE CONTROL OPERATION

Programming

The Remote Control

The Universal

Remote Control can be programmed

operate

many

manufacturers'

components,

using the

component

function

buttons for VCR,

DVD, CABLE

DBS. Follow the procedures for programming your Remote

Control with or without a code for the component.

TV (Panasonic

Only)

Panasonic Code

VCR

VCR (Preset)

Panasonic Code

DBS/OBL

DBS STB & CBL STB (Preset)

Panasonic DBS Code

DVD

DVD (Preset)

Panasonic Code

Note:

Determine

the manufacturer

of the component

and look

in the table for the code

(found on page

11).

Procedure

Confirm

that the external

component

is plugged

in and

operating.

Turn the component

off.

ACTION

Press

and

together,

for

least

seconds.

After

seconds,

the

illuminated

mode

(component)

buttons

will

begin

to flash.

Release

the

ACTION

and POWER

buttons.

Press

appropriate

component

button

on the

Remote

Control

VCR,

DVD,

CABLE

DBS.

The

component

button

will illuminate

steadily

and all others

will go out.

Enter

the 3-digit

component

code

using

the

Remote

Control

numeric

keypad

(O ~ 9 buttons).

The component

button

will blink twice.

Press

the

Remote

Control

test

the

component.

the

procedure

was

successful,

the

component

will turn on and the component

key will blink

twice and then go out.

Note:

If the

component

does

not

operate

with

the

Remote

Control,

repeat

steps

3 through

6 using

another

code

(some

brands

have

multiple

codes).

If an incorrect

code

is entered,

or ff the procedure

takes

longer

than

seconds,

the programming

will fail.

Programming

Without

A Code

This procedure

searches

all codes

and is called

the

"sequence method."

Confirm

that the external

component

is plugged

in and

on.

Turn the component

off.

ACTION

Press

and

together,

for

least

seconds.

After

seconds,

the

illuminated

mode

(component)

buttons

will

begin

to flash.

Release

the

ACTION

and POWER

buttons.

Press

the appropriate

component

button

on the Remote

Control.

The

component

button

will

illuminate

steadily

and all others

will go out.

Press

the

button

to set the remote

control

into

the step and set mode.

Point the remote

control

towards

the component.

Note:

Press VOL

•

(the mode

key will blink three

times),

then

press

the

Remote

Control

button

to test

the

component.

Continue

this process

until the proper

code

is found.

If the procedure

was successful,

the component

will turn

on.

Each time you press

the VOL

•

button,

make

sure

that

the

component

key

blinks

twice

before

pressing

the

POWER

button.

ACTION

Once

the device

responds,

press

to store

the

code. The mode

(component)

button

will blink twice.

It may

take

many

attempts

before

the

correct

code

is found.

If you miss

a code,

press

41 VOL,

then press

the

button

to test the component.

Component

Codes

The Universal

Remote Control

is capable

of operating

many component

brands after entering

a code. Some

components

may not operate because the codes are not

available due to limited memory. The Universal

Remote

Control does not control all features found in each model.

III ii

i i

VCR

CABLE

DVD

IIII

DBS

IIII

10e