Panasonic BB-HCM580A Bedieningshandleiding - Pagina 3
Blader online of download pdf Bedieningshandleiding voor {categorie_naam} Panasonic BB-HCM580A. Panasonic BB-HCM580A 4 pagina's. Power over ethernet (poe) zoom mpeg-4 network camera
Ook voor Panasonic BB-HCM580A: Integratie Opmerking (10 pagina's)
Pagina afdrukken
Read the following information after setting up the camera according to the procedure described in the Setup Guide.
Connecting External Sensors
The camera's external I/O interface allows you to connect 2 devices (such as sensors, motion detectors, etc.) that can be used to trigger the camera's image
buffering and transferring features (see Section 2 Using Triggers to Buffer and Transfer Images in the Operating Instructions on the CD-ROM).
The external I/O interface has 6 terminals.
Terminal
G
GND terminal.
External sensor input 1. The camera can be triggered by either an open
1
circuit or a GND short-circuit.
G
GND terminal.
External sensor input 2. The camera can be triggered by either an open
2
circuit or a GND short-circuit.
External device control output. Allows you to control an external device
using the output buttons in the camera's operation bar (for example,
turning a light on or off).
• This terminal's behavior can be changed (see 7.4 Controlling the
External Output Terminal in the Operating Instructions on the CD-
3
ROM).
• This terminal is an open collector circuit. The maximum drawing
current is the same as terminal 4. Do not exceed the voltage of the
terminal 4.
DC power output terminal.
4
• 10.5–13 V DC
• Maximum load drive is 100 mA.
Note
• Do not push strongly on the external I/O interface with the pointed object. The
external I/O interface may get stuck into the unit, and you may not be able to
use it.
Connecting a Video Device (BB-HCM580A Only)
You can connect a TV or other video device (NTSC or PAL format) to the camera to monitor or record camera images. Connect the video device as shown below.
To TV
Video terminal
Connecting Audio/video Devices (BB-HCM581A Only)
You can connect an external microphone and external speaker to the camera to use the Listen and Talk features, respectively. For information about these
features, see 1.2.10 Audio Features in the Operating Instructions on the CD-ROM. You can also connect a TV or other video device (NTSC or PAL format) to the
camera to monitor or record camera images. Connect the devices as shown below.
Microphone cable
( 3.5 mm mini plug)
Speaker cable
( 3.5 mm stereo mini plug)
For speaker (red)
(Output impedance
560
line level)
For microphone (white)
(Plug-in power +3.3 V)
External I/O interface
Description
Composite video connector
Video cable
(customer-provided)
3.5 mm L-type (right angle) connector
To microphone
To speaker
To TV
Video cable
For TV (yellow)
Audio/video cord
Audio/video terminal
Circuit Diagram Example
Camera
*DC 10.5 V–13 V
Caution
• The external I/O interface is not capable of connecting directly to devices
that require large amounts of current. In some cases, a custom interface
circuit (customer-provided) may have to be used. Serious damage to the
camera may result if a device that exceeds its electrical capability is
connected to the external I/O interface.
• Low voltage/current circuits and high voltage/current circuits are used in
the camera circuit. All wiring should be performed by a qualified
electrician. Incorrect wiring could damage the camera and cause a fatal
electric shock.
• External devices connected to the camera's output terminals cannot be
controlled in the event of a network error or failure. Keep this in mind when
connecting door locks, heat-emitting devices, or other devices that may
be dangerous if they cannot be controlled.
Note
• Analog video output is disabled by default. See 7.5 Controlling the Analog
Video Output Signal in the Operating Instructions on the CD-ROM for more
information.
• If you use an external microphone, excessive cable length or a poor quality
cable can cause degradation in audio quality.
• The microphone cable should be no longer than 7 m (23 feet).
• Use a speaker with a built-in amplifier. The speaker connects to the camera with a
stereo audio cable similar to that used by your PC. The output signal is mono.
• Make sure the camera and speaker are turned off when connecting or
disconnecting the speaker cable, otherwise noise may be heard from the
speaker.
• The external microphone input does not correspond to a line level. Audio may
be distorted when the line level is input. Audio distortion will be solved if you
insert the following circuits. Under no circumstance should high-level audio,
such as from a speaker, be connected to this input terminal. Doing so is likely
to damage the camera.
Camera
Microphone Input
Relay
Light
12 V*
4
Door Sensor 2 (Alarm 2)
3
2
Door Sensor 1 (Alarm 1)
G
1
G
Resistor
Capacitor
Audio Line
Out
33 K
1 F
3