Panasonic P1SDU - SVGA LCD Projector Gebruiksaanwijzing - Pagina 30
Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Panasonic P1SDU - SVGA LCD Projector. Panasonic P1SDU - SVGA LCD Projector 42 pagina's. Lcd projector commercial use
Pagina afdrukken
On-screen display
Displayed for 30
seconds. Pressing any
More than 2 250 hours
button will clear the
display.
Remains displayed until
More than 2 500 hours
any button is pressed.
Lamp unit replacement procedure
NOTE:
B If the lamp usage time has passed 2 500 hours, the projector will switch to
standby mode after approximately 10 minutes of operation. The steps ) to
/ on the next page should thus be completed within 10 minutes.
# Disconnect the power cord
from the projector by following
the procedure on page 28, and
check that the area around the
lamp unit has cooled down.
$ Use a Phillips screwdriver to
turn the lamp unit cover fixing
screw at the bottom of the
projector, and then remove the
lamp unit cover.
Lamp unit cover
Lamp unit cover fixing screw
58-E
NGLISH
LAMP indicator
Illuminates red during
image projection and
standby mode.
% Use a Phillips screwdriver to
loosen the lamp unit fixing
screw until the screw turns
freely. Then hold the handle of
the lamp unit and gently pull the
lamp unit out from the projector.
Handle
A
B
Lamp unit fixing screw
& Insert the new lamp unit while
making sure that the direction
of insertion is correct, and then
use a Phillips screwdriver to
securely tighten the lamp unit
fixing screw.
When inserting the new lamp unit, be
sure to push it in at the point A and B.
' Install the lamp unit cover, and
then use a Phillips screwdriver
to securely tighten the lamp
unit cover fixing screw.
NOTE:
B Be sure to install the lamp unit
and the lamp unit cover
securely. If they are not securely
installed, it may cause the
protection circuit to operate so
that the power cannot be turned
on.
( Connect the power cord.
) Press the POWER button so
that a picture is projected onto
the screen.
NOTE:
B If the power cord was
disconnected during projection
when the projector was used
the last time, projection will
start after the power cord is
connected.
* Press the MENU button to
display the "MAIN MENU", and
then press the F or G button
to select "OTHER SETUP".
M E N U
P I C T U R E A D J U S T M E N T
P O S I T I O N A D J U S T M E N T
O T H E R S E T U P
L A N G U A G E S E T U P
S E C U R I T Y S E T U P
S D P I C T U R E S E T U P
S E L E C T
E N T E R
E X I T
+ Press the ENTER button to display
the "OTHER SETUP" menu, and
then press the F or G button to
select "LAMP RUNTIME".
O T H E R S E T U P
A U T O S I G N A L
O N
T V - S Y S T E M
A U T O
F R O N T / R E A R
F R O N T
D E S K / C E I L I N G
D E S K
H I G H L A N D
O F F
L A M P R U N T I M E
2 3 0 0 H
S X G A M O D E
S X G A
C T R L P A N E L
V A L I D
N R
O F F
S E L E C T
R E T R N
, Press and hold the ENTER button
for approximately 3 seconds.
The "LAMP TIME RESET" screen
will be displayed.
L A M P T I M E R E S E T
O K
C A N C E L
- Select "OK" by pressing the I I
or H H button on the remote
control unit and then press the
ENTER button.
The "POWER OFF" confirmation
screen will be displayed.
P O W E R O F F
[ P O W E R ] O K
NOTE:
B The "POWER OFF" screen will
disappear in five seconds.
B If the MENU button is pressed, the
"LAMP TIME RESET" screen and
the "POWER OFF" confirmation
screen will be cancelled.
. Press the POWER button to
turn off the power.
/ Disconnect the power cord
after the POWER button on the
projector illuminates red.
This will reset the cumulative
usage time for the lamp unit to "0".
E
-59
NGLISH