Panasonic PT-L520E Gebruiksaanwijzing - Pagina 19

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Panasonic PT-L520E. Panasonic PT-L520E 30 pagina's. Lcd projector

Pagina afdrukken

WHITE BALANCE R/G/B

(RGB only)

This is used to adjust the white areas of the

picture if they appear colourised. Press the I

button to make the selected colour lighter.

Press the H button to make the selected

colour stronger.

SIGNAL MODE

(RGB/YP

only)

This displays the type of signal which is

currently being projected.

Refer to the table on page 56 for details on

each type of signal.

Projecting sRGB-compatible

pictures

sRGB is an international colour reproduction

standard (IEC61966-2-1) established by the

International Electrotechnical Commission

(IEC). If you would like the colours in sRGB-

compatible pictures to be reproduced more

faithfully, make the following settings.

# # Press the F F or G G button to select

"PICTURE MODE", and then use the I I

or H H button to select "NATURAL".

$ $ Press the STANDARD (STD) button on

the remote control unit.

% % Press the F F or G G button to select

"COLOR TEMP.", and then use the I I

or H H button to select "STANDARD".

NOTE:

B sRGB is only enabled when RGB signals

are being input (when LAMP POWER has

been set to "HIGH").

36-E

NGLISH

Adjusting the position

When the input signal is RGB, first

press the AUTO SETUP button to

initiate automatic positioning.

If the optimum setting is not

obtained when AUTO SETUP is

carried out, adjust by the following

procedure.

Use the F and G buttons on the

projector or remote control unit to

select an item, and then use the I

and H buttons to change the setting

for that item.

For items with bar scales, press the

ENTER button or the I or H

buttons to display the adjustment

screen, and then use the I or H

buttons to make the adjustment.

When an RGB/YP

signal is

being input

P O S I T I O N

H - P O S I T I O N

6 4

V - P O S I T I O N

3 2

D O T C L O C K

3 2

C L O C K P H A S E

1 6

A S P E C T

4 : 3

R E S I Z I N G

O N

S T A N D A R D

S E L E C T

E N T E R

E S C

When an S-VIDEO/VIDEO signal is

being input

P O S I T I O N

H - P O S I T I O N

3 2

V - P O S I T I O N

1 6

A S P E C T

4 : 3

R E S I Z I N G

O N

S T A N D A R D

S E L E C T

E N T E R

E S C

HORIZONTAL POSITION

Press the I button to move the

picture to the left, and press the H

button to move the picture to the right.

VERTICAL POSITION

Press the I button to move the

picture down, and press the H

button to move the picture up.

DOT CLOCK

(RGB only)

Periodic striped pattern interference

(noise) may occur when a striped

pattern such as the one below is

projected. If this happens, use the

I and H buttons to adjust so that

any such noise is minimised.

CLOCK PHASE

(RGB/YP

only)

Adjust the DOT CLOCK setting first

before carrying out this adjustment.

Use the I and H buttons to adjust

so that the noise level is least

noticeable.

NOTE:

B If signals with a dot clock frequency

of 100 MHz or higher are being input,

interference may not be completely

eliminated when the DOT CLOCK

and CLOCK PHASE adjustments are

carried out.

-37

NGLISH