Panasonic SA-EN29 Gebruiksaanwijzing - Pagina 11
Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Panasonic SA-EN29. Panasonic SA-EN29 12 pagina's. Cd stereo system model no. sc-en29
Pagina afdrukken
Control guide
The shaded buttons, such as
, function in the same way as the buttons on
the remote control.
Troubleshooting guide
Before requesting service, make the following checks. If you are in doubt about any of the check points, or if the solutions indicated in the chart do not solve the problem,
consult your dealer for instructions.
• The disc isn't correctly set.
• The disc is scratched or dirty. (Tracks skipped.)
No play.
• There is moisture on the lens. Wait about an hour
and then try again.
• You may not be able to play MP3 if you have copied a
multi-session disc that has no data between sessions.
• When creating a multi session disc, it is necessary
MP3 cannot be read.
to close the session.
• The amount of data on the disc is too small. Set the
amount of data to greater than approximately 5 MB.
Sound is unfixed,
reversed or comes
• Check the speaker connections. (
from one speaker only.
• Noise may occur when playing MP3 if recording quality is poor.
• Keep this unit away from mobile telephones.
• Turn the volume up.
No sound or there is
• Switch the unit off, determine and correct the cause, then switch
a lot of noise.
the unit on. Causes include shorting of the positive and negative
speaker wires, straining of the speakers through excessive
volume or power, and using the unit in a hot environment.
Humming heard
• An AC mains lead or fluorescent light is near the cords. Keep
during play.
other appliances and cords away from this unit's cords.
A beat sound is
heard while receiving
• Switch the TV off or separate it from the unit.
a radio broadcast.
A low hum or noise
• Keep the antenna away from other cables and
is heard during AM
cords.
broadcasts.
• Keep the AM antenna away from the unit.
The picture on the
• The location and orientation of the antenna are
television near the set
incorrect.
disappears or stripes
• The TV antenna wire is too close to the unit. Separate
appear on the screen.
the antenna wire of the TV set from the unit.
• Keep the antenna away from computers, televisions,
DAB reception is
other cables and cords.
poor.
• Use an outdoor antenna (
Remote control
• Check that the batteries are inserted correctly. (
doesn't work.
• Replace the batteries if they are worn.
Standby/on switch [8, ^] .............................................................. 4
Press to switch the unit from on to standby mode or vice versa.
In standby mode, the unit is still consuming a small amount of power.
The unit is in the standby condition (the [
AC mains lead is connected.
The primary circuit is always "live" as long as the AC adaptor is
connected to an electrical outlet.
Clock/timer adjust button [CLOCK/TIMER ADJ] ......................... 9
SLEEP timer button [SLEEP]......................................................... 9
CD program/clear, FM/AM/DAB preset button [PGM/CLEAR]....... 4, 5, 7
Play mode button [PLAY MODE] ......................................... 4, 5, 10
DAB primary/secondary select button [PRIMARY/SECONDARY] .............. 7
AUX button [AUX] ......................................................................... 10
Tuner/band select button [TUNER/BAND] .................................... 5
DAB button [DAB].......................................................................... 6
Volume buttons [VOL –, + VOL]..................................................... 4
Extra D.Bass button [EXTRA D.BASS] ......................................... 9
Sound EQ button [SOUND EQ] ..................................................... 9
Album skip, FM/AM/DAB preset channel select buttons
[2, 1, u ALBUM i] ........................................................ 5, 7, 10
Display button [DISPLAY] .......................................................... 7, 9
Timer set/check button [TIMER SET/CHECK] .............................. 9
Numbered buttons [1–9, 0, 10] .................................................... 4
CD play/pause button [CD q/h] .................................................... 4
CD stop button [g] ......................................................................... 4
Live virtualizer button [LIVE VIRTUALIZER] ................................ 9
CD skip/search, FM/AM frequency select, DAB station tune,
time adjust buttons [u, i, –, +] ................................... 4, 5, 6, 9
DAB menu buttons [MENU, –, +, ENTER] ..................................... 8
Standby indicator
When the unit is connected to the AC adaptor, this indicator lights up
in standby mode and goes out when the unit is turned on.
Remote control signal sensor
CD skip/search, FM/AM frequency select, DAB station tune,
FM/AM/DAB preset channel select buttons [u/–, +/i] ..... 4, 5, 6, 7
Tuning mode select button [TUNING MODE] ....................... 5, 6, 7
Display
Function indicators ................................................................ 4, 5, 6
The indicator lights up when each mode is chosen.
DAB/DAB auto scan button [DAB] ............................................ 6, 7
CD open/close button [; OPEN/CLOSE]...................................... 4
No response even
when button is
pressed.
I want to erase the
memory and reset it.
Display
– –:– –
– – –:– –
page 3)
PROGRAM FULL
NOT MP3 DISC
ERROR
NO SERVICE
NO SIGNAL
DATA
SCRAMBLE
Scan Failed.
F
stands for a number.)
STATION FULL
page 10).
page 3)
^
] indicator lights) when the
> =
• Use the following method to initialize the settings.
1.Remove the AC adaptor.
^
2. While pressing [
/I ] on the unit, insert the AC adaptor.
3.While continuing to press and hold [
"----------------" appears.
• You plugged the AC adaptor in for the first time or there was a
power failure recently. Set the time. (
• The total programmed play time is more than 200 minutes.
Tracks can still be programmed and played.
• The number of programmed tracks is limited to 24.
No further tracks can be programmed.
• A CD-ROM disc that is not CD-DA or MP3 format is
inserted. It cannot be played.
• Incorrect operation performed. Read the instructions and try again.
• The station is currently not broadcasting.
• This station cannot be received. Check your antenna (
• Data broadcast being received over the DAB
broadcast signal. Cannot be used on this unit.
• The broadcast station being received cannot be
accessed (E.g. pay per use etc.).
• Stations are not receivable. Check your antenna
and try Auto scanning (
page 3, 7).
• Turn the unit off, disconnect the AC adaptor, and
consult your dealer.
• DAB station memory is full. Use the following
method to clear station memory.
1. Press [MENU].
2. Press [–] or [+] to select "STATION CLEAR".
3. Press [ENTER]. "OK? Push ENTER" is displayed.
4. Press [ENTER].
Station memory is erased and the unit automatically
begins Auto scanning.
^
/I ] ,
page 8, 9)
page 3).
11
RQT8538