Bionaire BH3950 Gebruiksaanwijzing - Pagina 2

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Bionaire BH3950. Bionaire BH3950 2 pagina's. Silent whole room heater
Ook voor Bionaire BH3950: Gebruiksaanwijzing (2 pagina's)

Pagina afdrukken

BH395006EM1.qxd

6/6/06

16:50

Page 2

11. A heater has hot and arcing or sparking parts inside.

HEATER SAFETY

DO NOT use it in areas where gasoline, paint, or flam-

mable liquids are used or stored.

PLEASE READ AND SAVE

12. Use appliance only for intended household use as

described in this manual. Any other use not recom-

THESE IMPORTANT

mended by the manufacturer may cause fire, electric

SAFEGUARDS

shock, or injury to persons. The use of attachments not

recommended or sold by The Holmes Group may

cause hazards.

IMPORTANT INSTRUCTIONS

13. DO NOT use outdoors.

When using electrical appliances, basic safety precautions

14. To prevent a possible fire, DO NOT block air intakes or

should always be followed to reduce the risk of fire, electric

exhaust in any manner. DO NOT use on soft surfaces,

shock, and injury to persons, including the following:

like a bed, where openings may become blocked.

1. Read all instructions before using the appliance.

15. To disconnect heater, turn controls to Off, then remove

2. To avoid fire or shock hazard, plug the appliance direct-

plug from outlet.

ly into a 120V AC electrical outlet.

16. Avoid the use of an extension cord because the exten-

3. The heater is hot when in use. To avoid burns, DO

sion cord may overheat and cause a risk of fire.

NOT let bare skin touch hot surfaces. If provided, use

However, if you have to use an extension cord, the

handles when moving this heater. Keep combustible

cord should be No. 14AWG minimum size and rated

materials, such as furniture, pillows, bedding, papers,

not less than 1875 watts.

clothes, and curtains at least 3 ft (0.9 m) from the front

17. If the heater will not operate, see specific instructions

of the heater and keep them away from the sides and

on Auto Safety Shut-off.

rear.

18. DO NOT attempt to repair or adjust any electrical or

4. DO NOT run cord under carpeting. DO NOT cover

mechanical functions on this unit. Doing so will void

cord with throw rugs, runners, or the like. Arrange cord

your warranty. The inside of the unit contains no user

away from traffic area and where it will not be tripped

serviceable parts. All servicing should be performed by

over.

qualified personnel only.

5. This heater is not intended for use in bathrooms, laun-

19. DISCONTINUE USE IF PLUG OR OUTLET IS HOT.

dry areas and similar indoor locations. NEVER locate

RECOMMEND OUTLET BE REPLACED IF PLUG OR

heater where it may fall into a bathtub or other water

OUTLET IS HOT TO TOUCH.

container.

6. Extreme caution is necessary when any heater is used

by, or near children or invalids, and whenever the

heater is left operating and unattended.

7. Always unplug the heater when not in use.

8. When unplugging, be sure to pull by the plug and not

the cord.

9. DO NOT insert or allow foreign objects to enter any

ventilation or exhaust opening as this may cause an

electric shock or fire, or damage the heater.

10. DO NOT operate heater with a damaged cord or plug,

or after the heater malfunctions, or has been damaged

in any manner. Return appliance to manufacturer for

examination, electrical or mechanical adjustment, or

repair.

PLEASE SAVE THESE

ASSEMBLY INSTRUCTIONS

INSTRUCTIONS

Handle / Wheel / Front Foot Assembly

There are two wheels, one axle, one front foot, two screws,

and a handle packed within the box that you will need to

CONSUMER SAFETY INFORMATION

attach to the heater (Please refer to Fig.1 - 6).

THIS PRODUCT IS EQUIPPED

1. Using force, attach the provided handle to the front

WITH A POLARIZED AC PLUG

housing of the heater (as shown in Fig.1). The handle

(a plug having one blade wider

will snap into place and was not meant to be taken

than the other). This plug will fit

apart after attached to the heater.

into the power outlet only one

2. Turn the heater upside down.

way. If the plug does not fit fully

3. Place the foot onto the bottom of the front housing

into the outlet, reverse the plug. If it still does not fit, con-

(same side as control panel and as shown in Fig.2).

tact qualified personnel to install the proper outlet.

Secure the foot with one of the provided screws (as

DO NOT DEFEAT THE SAFETY PURPOSE OF THIS

shown in Fig.3).

POLARIZED PLUG IN ANY WAY.

4. Place the wheel axle onto the bottom of the back

housing (same side as power cord and as shown in

PLEASE READ AND SAVE

Fig.4). Secure the axel with the second provided

screw (as shown in Fig.5).

THESE IMPORTANT

5. Using force, insert a wheel into one of the two holes of

SAFETY INSTRUCTIONS

the axel (repeat with second wheel) (as shown in Fig.6).

They will snap into place and are not meant to be

taken apart after attached to the axle.

TECHNICAL SPECIFICATIONS

NOTE: This unit cannot operate without the feet properly

Wattage:

1500W/ (+ 5% - 15%)

secured on the bottom of the heater.

Working Voltage:

120V AC/60 HZ

AUTO SAFETY SHUT-OFF

Fig.1

This heater is equipped with a patented, technologically-

advanced, safety system that automatically shuts off the current

to the heater when a potential overheat temperature is reached.

The heater can only resume operation when you reset it.

To Reset the Heater

If your heater shuts down, follow these steps:

1. Turn Mode to OFF and Thermostat to High.

2. Unplug the heater and wait 30 minutes.

3. Plug in the heater and turn the Mode to High

Fig.3

4. Your heater should now be operating properly.

Tip-Over Shut-Off

If the heater is knocked over, it will instantly shut off. To

reset, simply place the heater in an upright position and

turn ON the heater.

PRE-OPERATING INSTRUCTIONS

1. Carefully remove your heater from the box.

2. Make sure the heater is OFF before plugging the heater

into the outlet.

3. Place the heater on a firm, level surface.

4. Avoid overloading your circuit by not using other high

wattage appliances in the same outlet. At 1500 Watts,

this unit draws 12.5 Amps.

SETTING THE THERMOSTAT

1. Before setting the Thermostat, turn the Mode Button to

HI and allow the heater to warm up the room.

2. When the desired comfort level is reached, lower the

Thermostat until the heater stops.

3. The control now maintains the selected comfort level

by automatically turning the heater ON and OFF.

4. The Temperature light turns on and remains lit when

the selected comfort level is reached.

NOTE: It is normal for the heater to cycle ON and OFF as

it maintains the programmed temperature. To prevent the

heater from cycling, raise the thermostat setting.

Fig.7

Fig.2

Fig.4

Fig.5

Fig.6

A. Power Button

C. Thermostat Button

(Temperature Light)

D. Power Indicator

B. Mode Button

(HI = II, LO = I )

CLEANING/MAINTENANCE

Always unplug the heater before cleaning.

• Lightly run a vacuum cleaner nozzle over the heater grill

to remove any dust or dirt that may have accumulated.

• Carefully wipe the heater with a soft, damp cloth. Please

be very cautious near the heating elements.

• NEVER use abrasive or flammable solvents to clean the

heater.

• After cleaning, be sure to completely dry the heater with

a cloth or towel.

• Store your heater in a cool, dry location.

TROUBLESHOOTING

If your heater fails to operate, unplug the heater and:

• Make sure the electrical outlet and circuit breaker are

working.

• Check for obstructions. If you find an obstruction, turn

OFF and UNPLUG the heater. Carefully remove the

obstruction and follow the reset instructions.

• Check the thermostat setting; it might be set too low. Turn

the thermostat dial clockwise until the heater restarts.

• Make sure the Mode Control is on the Lo or Hi setting.

Please DO NOT attempt to open or repair the heater.

Please see the Warranty for Service Instructions or

call our Consumer Services Department at

1-800-253-2764.