Bionaire BH3950 Gebruiksaanwijzing - Pagina 2

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Bionaire BH3950. Bionaire BH3950 2 pagina's. Silent whole room heater
Ook voor Bionaire BH3950: Gebruiksaanwijzing (2 pagina's)

Pagina afdrukken

P L E A S E R E A D A N D S AV E T H E S E

I M P O R TA N T S A F E T Y I N S T R U C T I O N S

When using electrical appliances, basic safety precautions

11. To prevent a possible fire, do not block air intakes or

should always be followed to reduce the risk of fire, electric

exhaust in any manner. Do not use on soft surfaces,

shock, and injury to persons, including the following:

like a bed, where openings may become blocked.

12. A heater has hot and arcing or sparking parts inside.

1. Read all instructions before using this heater.

Do not use it in areas where gasoline, paint, or

2. This heater is hot when in use. To avoid burns, do not

let bare skin touch hot surfaces. If provided, use

flammable liquids are used or stored.

13. Use this heater only as described in this manual. Any

handles when moving this heater. Keep combustible

other use not recommended by the manufacturer

materials, such as furniture, pillows, bedding, papers,

may cause fire, electric shock, or injury to persons.

clothes, and curtains at least 3 feet (0.9 m) from the

14. Always plug heaters directly into a wall outlet/

front of the heater and keep them away from the

receptacle. Never use with an extension cord or

sides and rear.

3. Extreme caution is necessary when any heater is used

relocatable power tap (outlet/power strip).

by or near children or invalids and whenever the

15. When unplugging, be sure to pull by the plug and

heater is left operating and unattended.

not the cord.

4. Always unplug heater when not in use.

16. If the heater will not operate, see specific instructions

on Auto Safety Shut-off.

5. Do not operate any heater with a damaged cord or

17. DO NOT attempt to repair or adjust any electrical or

plug or after the heater malfunctions, has been

dropped or damaged in any manner. Discard heater,

mechanical functions on this unit. Doing so will void

your warranty. The inside of the unit contains no user

or return to authorized service facility for

serviceable parts. All servicing should be performed

examination and/or repair.

by qualified personnel only.

6. Do not use outdoors.

18. Discontinue use if plug or outlet is hot. It is

7. This heater is not intended for use in bathrooms,

recommended that the outlet be replaced if plug or

laundry areas and similar indoor locations. Never

locate heater where it may fall into a bathtub or

outlet is hot to touch.

19. The heater must not be located immediately below a

other water container.

socket-outlet. Do not use this heater in the immediate

8. Do not run cord under carpeting. Do not cover cord

surroundings of a bath, a shower or a swimming pool.

with throw rugs, runners, or similar coverings. Do not

NOTE: THIS UNIT IS FOR FLOOR USE ONLY.

route cord under furniture or appliances. Arrange

cord away from traffic area and where it will not be

tripped over.

SAVE THESE

9. To disconnect heater, turn controls to off, then

remove plug from outlet.

INSTRUCTIONS

10. Do not insert or allow foreign objects to enter any

ventilation or exhaust opening as this may cause an

electric shock or fire, or damage the heater.

THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the

other). To reduce the risk of electric shock, this plug is intended to fit in a

polarized outlet only one way. If the plug does not fit fully in the outlet,

reverse the plug. If it still does not fit, contact a qualified electrician to

install the proper outlet.

DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS

SAFETY FEATURE IN ANY WAY.

BH3950_12EM1.indd 2

F E AT U R E S - O P E R AT I O N S

NOTE:

ASSEMBLY INSTRUCTIONS

•

There may be an odor coming from the heater the

Handle / Wheel / Front Foot Assembly

first time you use it. This is normal during the break-

There are two wheels, one wheel mounting bracket, one

in period. Make sure the heater is in a well

front foot, two screws, and a handle packed within the box

ventilated area and continue running it until the

that you will need to attach to the heater (Please refer to

smell goes away.

Figs.1–6). NOTE: Wheel assembly must go on the back and

•

You may hear a popping or crackling sound as the

stand assembly must go on the front.

heater heats up. This is normal and safe operation.

1. Push the handle into the front housing of the heater

Once the heater heats up, the crackling sound will

(as shown in Fig. 1). The handle will snap into place

go away.

and is not meant to be taken apart after it is attached

to the heater.

TECHNICAL SPECIFICATIONS

2. Turn the heater upside down.

Wattage:

3. Place the foot onto the bottom of the FRONT of the

1500W/ (+ 5% - 10%)

heater (same side as control panel and as shown in

Fig.2). Secure the foot with one of the provided

Working Voltage:

screws (as shown in Fig.3).

120V AC/60 HZ

4. Place the wheel mounting bracket onto the bottom of

the back of the heater (as shown in fig. 4), (same

AUTO SAFETY SHUT-OFF

side as the power cord). Secure the wheel mounting

This heater is equipped with a patented, technologically-

bracket with the second screw provided (as shown in

advanced, safety system that automatically shuts off the

Fig.5).

current to the heater when a potential overheat

temperature is reached. The heater can only resume

Fig.1

operation when you reset it.

TO RESET THE HEATER

If your heater shuts down, follow these steps:

1. Turn Power (button A) to OFF (O) and Thermostat to

High (fully clockwise).

2. Unplug the heater and wait 30 minutes.

3. Plug in the heater, turn the power ON, and turn the

Heat level button (B) to High ( l l ).

Fig.2

Fig.3

4. Your heater should now be operating properly.

TIP-OVER SHUT-OFF

If the heater is knocked over, it will instantly shut off. To

BH3950 heater 3/06

resume operation, simply place the heater in an upright

position and turn ON the heater.

F E AT U R E S - O P E R AT I O N S

Fig.5

Fig.6

Fig.7

5. Using force, insert the wheel into one of the holes on

each side of the mounting bracket (as shown in

Fig.6). They will snap into place and are not meant

BH3950 heater 3/06

to be taken apart after assembly.

BH3950 heater 3/06

NOTE: This unit should not be operated without the feet

properly secured on the bottom of the heater.

PRE-OPERATING INSTRUCTIONS

1. Carefully remove your heater from the box.

A. Power Button

2. Make sure the heater is OFF before plugging the

( I = ON, O = OFF ),

heater into the outlet.

(This is also the Temperature Light)

B. Heat Level Button

3. Place the heater on a firm, level surface.

( HI = II, LO = I )

4. Avoid overloading your circuit by not using other

C. Thermostat Knob

high wattage appliances in the same outlet. At 1500

D. Power Indicator

Watts, this unit draws 12.5 Amps.

5. The system now maintains the selected comfort level

OPERATING INSTRUCTIONS

by automatically turning the heater ON and OFF.

1. Turn Power ON (button A). Depress ( l ).

NOTE: The Temperature light cycles ON and OFF with the

2. Turn Thermostat knob (C) fully clockwise.

heater element as it maintains the programmed

3. Depress Heat Level button to high ( l l ), and allow

temperature. To prevent the heater from cycling, raise

Fig.4

the heater to warm up.

the thermostat setting.

4. When the desired comfort level is reached, lower the

Thermostat until the heater stops and the

temperature light turns off.

C L E A N I N G / M A I N T E N A N C E

CLEANING/MAINTENANCE

If you have any questions regarding your product or

would like to learn more about other Bionaire

Always unplug the heater before cleaning. And allow

to cool.

products, please contact our Consumer Service

Department at 1-800-253-2764 or visit our website

• Lightly run a vacuum cleaner nozzle over the heater

at www.bionaire.com.

grill to remove any dust or dirt that may have

accumulated.

• Carefully wipe the heater with a soft, damp cloth.

Please be very cautious near the heating elements.

• NEVER use abrasive or flammable solvents to clean

the heater.

• After cleaning, be sure to completely dry the heater

with a cloth or towel.

• Store your heater in a cool, dry location.

TROUBLESHOOTING

If your heater fails to operate or if there is no heat:

• Make sure the power button is ON. Depress ( l ) on

button A.

• Check the thermostat setting; it might be set too low.

Turn the thermostat knob clockwise until the heater

restarts.

• If the unit is still not producing enough heat, make

sure the Heat Level button is on the high setting

( l l is depressed ).

• Be patient. Give the heater time to heat up.

• Check for obstructions. If you find an obstruction, turn

OFF and UNPLUG the heater. Carefully remove the

obstruction and follow the reset instructions.

• Make sure the electrical outlet and circuit breaker are

working.

Please DO NOT attempt to open or repair the heater.

Please see the Warranty for Service Instructions or call our

Consumer Services Department at

1-800-253-2764.

2/8/12 2:59 PM