Bionaire BQH308C Gebruiksaanwijzing - Pagina 2

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Bionaire BQH308C. Bionaire BQH308C 2 pagina's. Tower quartz heater
Ook voor Bionaire BQH308C: Gebruiksaanwijzing (2 pagina's), Gebruiksaanwijzing (2 pagina's)

Pagina afdrukken

P L E A S E R E A D A N D S AV E T H E S E

I M P O R TA N T S A F E T Y I N S T R U C T I O N S

When using electrical appliances, basic safety precautions

11. A heater has hot and arcing or sparking parts inside.

should always be followed to reduce the risk of fire, electric

DO NOT use it in areas where gasoline, paint, or

shock, and injury to persons, including the following:

flammable liquids are used or stored.

12. Use appliance only for intended household use as

1. Read all instructions before using the appliance.

described in this manual. Any other use not

2. To avoid fire or shock hazard, plug the appliance

recommended by the manufacturer may cause fire,

directly into a 120V AC electrical outlet.

electric shock, or injury to persons. The use of

3. The heater is hot when in use. To avoid burns, DO

attachments not recommended or sold by the

NOT let bare skin touch hot surfaces. If provided, use

manufacturer may cause hazards.

handles when moving this heater. Keep combustible

13. DO NOT use outdoors.

materials, such as furniture, pillows, bedding, papers,

14. To prevent a possible fire, DO NOT block air intakes or

clothes, and curtains at least 3 ft (0.9 m) from the

exhaust in any manner. DO NOT use on soft surfaces,

front of the heater and keep them away from the

like a bed, where openings may become blocked.

sides and rear.

15. To disconnect heater, turn controls to OFF, then

4. DO NOT run cord under carpeting. DO NOT cover

remove plug from outlet.

cord with throw rugs, runners, or the like. Arrange

16. Avoid the use of an extension cord because the

cord away from traffic area and where it will not be

extension cord may overheat and cause a risk of

tripped over.

fire. However, if you have to use an extension cord,

5. This heater is not intended for use in bathrooms,

the cord shall be No. 14 AWG minimum size and

laundry areas and similar indoor location. NEVER

rated not less than 1875 watts.

locate heater where it may fall into a bathtub or

17. If the heater will not operate, see specific instructions

other water container.

on Auto Safety Shut-off.

6. Extreme caution is necessary when any heater is

18. DO NOT attempt to repair or adjust any electrical or

used by, or near children or invalids, and whenever

mechanical functions on this unit. Doing so will void

the heater is left operating and unattended.

your warranty. The inside of the unit contains no user

7. Always unplug the heater when not in use.

serviceable parts. All servicing should be performed

8. When unplugging, be sure to pull by the plug and

by qualified personnel only.

not the cord.

19. Discontinue use if plug or outlet is hot. It is

9. DO NOT insert or allow foreign objects to enter any

recommended that the outlet be replaced if plug or

ventilation or exhaust opening as this may cause an

outlet is hot to touch.

electric shock or fire, or damage the heater.

20. The heater must not be located immediately below a

10. DO NOT operate heater with a damaged cord or

socket-outlet. Do not use this heater in the

plug, or after the heater malfunctions, has been

immediate surroundings of a bath, a shower or a

dropped or damaged in any manner. Return

swimming pool.

appliance to manufacturer for examination, electrical

NOTE: This unit is for FLOOR USE ONLY.

or mechanical adjustment, or repair.

THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the

other). To reduce the risk of electric shock, this plug is intended to fit in a

polarized outlet only one way. If the plug does not fit fully in the outlet,

reverse the plug. If it still does not fit, contact a qualified electrician to

install the proper outlet.

DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS

SAFETY FEATURE IN ANY WAY.

BQH308C-U_10EM1.indd 2

F E AT U R E S - O P E R AT I O N S

PLEASE READ AND SAVE

Mode Control

Turn the Mode Control to the desired setting:

THESE IMPORTANT

- Off Mode

SAFETY INSTRUCTIONS

To shut off the heater at any time of operation, turn the

Mode Control to Off (

1 - Low Heat

TECHNICAL SPECIFICATIONS

The heater will run continuously at 750W.

• Amps: 12.5

2 - High Heat

• Wattage: 1500W (+5% -10%)

The heater will run continuously at 1500W.

• Working Voltage: 120V AC/60 Hz

Thermostat Control

MAXFLOW

FAN SYSTEM

1. Set thermostat to the highest setting to start heater

(See Figure 1). Allow heater to operate and warm up

The patented MaxFlow

Fan system incorporates a top

the room.

mounted fan and internal shroud to provide maximum

2. When the desired temperature/comfort level is

heat dispersion. The MaxFlow

Fan system delivers a

reached, lower the thermostat setting until the fan/

combination of instant, penetrating warmth in the

heater stops operating.

immediate area, as well as forcing heat out for entire

3. The control will now automatically maintain the preset

room coverage.

temperature level by turning the heater ON and OFF.

NOTE: It is normal for the heater to cycle ON and OFF as

OPERATING INSTRUCTIONS

it maintains the preset temperature. To prevent the unit

from cycling, raise the thermostat to the highest setting.

1. Carefully remove your heater from the box. Please

save the carton for off-season storage.

Figure 1

2. Make sure the unit is in the OFF (

) position

before plugging the heater into the outlet.

3. Avoid overloading your circuit by not using other high

wattage appliances in the same outlet. At 1500

Watts, this unit draws 12.5 Amps.

4. For heater operation, please set the Thermostat all

the way to the highest setting. (See Figure 1)

NOTE: This unit is for FLOOR USE ONLY.

NOTE: Discontinue use if plug or outlet is hot.

NOTE: Recommend outlet be replaced if plug or outlet is

hot to touch.

NOTE: You may notice vibration/noise coming from the

A. Thermostat

grill and the interior quartz tubes when the heater is

B. OFF

turned on. PLEASE NOTE THAT THIS IS NORMAL AND SAFE

C. Heat Control Display

OPERATION. Once the quartz heating element has

warmed up, the vibration/noise will go away.

C L E A N I N G / M A I N T E N A N C E

CLEANING/MAINTENANCE

Always unplug the heater before cleaning and allow the

heater to cool down.

1. Clean the unit with a soft cloth moistened with a mild

soap and water solution.

) position.

2. NEVER use abrasive or flammable solvents to clean

the unit.

3. After cleaning, be sure to completely dry the unit

with a cloth or towel.

4. Store heater in a cool, dry location.

5. It is recommended that you store the unit in its

original carton.

TIP: Over time, dust may accumulate on the front

grills. This can be removed by wiping the unit with a

damp cloth.

AUTO SAFETY SHUT-OFF WITH INSTANT

TIP-OVER PROTECTION

This heater is equipped with a patented, technologically-

advanced safety system that requires the user to reset the

heater if there is a potential overheat situation. When a

potential overheat temperature is reached, the system will

automatically shut the heater off. It can only resume

operation when the user resets the unit.

To Reset the Heater:

1. Turn the Heat Control to the OFF (

2. Wait 30 minutes for the unit to cool down.

3. After the 30 minutes, plug the unit in again and

operate normally.

Tip-Over Shut Off:

When the unit is accidentally knocked over, it will instantly

shut off. The unit may also shut off if it is moved or

bumped. To reset, simply place the heater in an upright

position and it will operate normally.

NOTE: If unit does not turn on when placed in the

D. HI (2) 1500 Watts

upright position, turn the Mode Control to High (2) setting

E. LO (1) 750 Watts

and heater will resume operation.

F. Mode Control

TROUBLESHOOTING

If your heater fails to operate:

• The temperature may be set too low. Turn the

thermostat knob clockwise until the heater restarts.

• Make sure selector is in LO (1) or HI (2) setting.

• UNPLUG THE UNIT and make sure the heater is

placed in an upright position.

• Make sure the electrical outlet or circuit breaker is

working.

• Check for obstructions. If you find an obstruction turn

the heater OFF, and unplug the unit. Carefully

remove the obstruction and follow the reset

instructions.

Please DO NOT attempt to open or repair the

heater.

If you have any questions regarding your product or

would like to learn more about other Bionaire

products, please contact our Consumer Service

Department at 1-800-253-2764 or visit our website at

www.bionaire.com.

) position.

2/3/10 10:12:17 AM