Alpha Communications TekTone CM800 Handleiding voor installatie en gebruik - Pagina 2

Blader online of download pdf Handleiding voor installatie en gebruik voor {categorie_naam} Alpha Communications TekTone CM800. Alpha Communications TekTone CM800 8 pagina's. Emergency call signaling system

Pagina afdrukken

BE005/BE007 Corridor Bells: Locate BE005 and BE007 Cor-

ridor Bells in corridor above door height. Location in corridor

will be determined by the number of bells required on each

floor.

SS106 Transformer: Locate SS106 in an accessible area near a

source of 117 VAC. Observe local codes.

Wiring Installation

Run wiring conduit from corridor light to corridor light and

terminate at the CM800 or CM900 annunciator panel. Select

conduit size according to the application, as shown in wiring

diagrams in this booklet. Observe local codes.

PK2019, PK2019A Options:

• For 30-second delay before tone, connect terminal A to

terminal N.

• For steady tone, connect terminal W to terminal N. If the

annunciator lamp is flashing, the tone will be intermittent

despite terminal W connection.

Housing Installation

CM800, CM900 Annunciators:

Flush Wall Mount—Provide a wall cutout as shown in

Figure 1. Fit the back box and frame assembly into the

prepared opening. Fasten the assembly in place. Note: The

back box must be TekTone

Surface Wall Mount—Fasten the back box and frame

assembly to the wall through the holes provided in back of

the box, using suitable fasteners. Note: Back box must be

TekTone

OH300 Series.

SF117 series, SF118 series, SF154 Emergency Call Stations:

Install single gang ring (or single gang ring and double gang

box) as shown in Figure 2 for each emergency call station

in system. Minimum dimensions of back box must not be less

than 4"×4"×1.5". Minimum opening on ring must not be less

than 1.75"×2.75". Minimum clearance from live parts of the

station to dead metal parts must not be less than 0.5".

Page 2 • IL514 CM800/CM900 Emergency Call System Manual

OH200 Series.

IR019, IR019B Remote Annunciator Tone Speakers: Install

double gang ring (or double gang ring and double gang box)

as shown in Figure 3 for each tone speaker station. Mini-

mum dimensions of back box must not be less than

4"×4"×1.5".

LI118B, LI123B Corridor Lights: Install double gang ring (or

double gang ring and double gang box) as shown in Fig-

ure 3 for each tone speaker station. Minimum dimensions of

back box must not be less than 4"×4"×1.75".

LI381, LI382 Corridor Lights: Install double gang ring (or

double gang ring and double gang box) as shown in Fig-

ure 3 for each corridor light. Minimum dimensions of back

box must not be less than 4"×4"×1.5". Minimum opening on

ring must not be less than 2.75"×2.75". Minimum clearance

from live parts of the station to dead metal parts must not be

less than 0.5".

LI382LED Corridor Zone Light: Install standard one- or two-

gang box with one- or two-gang ring as shown in Figure 3

for each tone speaker station. Minimum clearance from live

parts of the station to dead metal parts must not be less than

0.5".

BE005, BE007 Corridor Bells: Install a standard 4" Bell Box.

Wire Checkout

Use an ohmmeter or other continuity checking device to test

wires for shorts or grounds. If shorts or grounds are

encountered, find and correct the problems before continuing.

Make sure the minimum number of conductors that are needed

for all of the equipment being used in the system are available.

Connections Checkout

Re-check all connections to equipment. If all wires and

connections are satisfactory, connect the primary coil of the

SS106 Transformer to a source of 117 VAC 60 Hz (30 VA max.).