Axis 290A Installatiehandleiding - Pagina 2

Blader online of download pdf Installatiehandleiding voor {categorie_naam} Axis 290A. Axis 290A 4 pagina's. Outdoor housing
Ook voor Axis 290A: Handleiding voor installatie-instructies (8 pagina's)

Pagina afdrukken

290A Installation Guide

3. Installing your housing with camera

outside

Recommendation: Keep the housing closed at all possible

times. This prevents the build-up of dirt, dust, moisture or

water inside the housing and any subsequent problems that

could arise from it once in operation.

Important: Only certified electrical technicians should install

this product, else the warranty will not be valid. You are re-

sponsible for correct and safe installation of this product and

compliance of the installation with local laws and regula-

tions.

Warning: Apparatus works on 100-240VAC. Danger of elec-

trical shock. Always ensure that mains is disconnected before

starting any work or opening the housing.

3.1. Route the cables (CAT.5 and mains power) to the point

of fix (this is your own responsibility and no instruc-

tions on how to do this are given here, nor is it avail-

able). Refer to chapter 6 of this manual if the cables are

not coming out of the wall at the point of fix. Else con-

tinue with 3.2.

3.2. Detach the bracket from the housing by unscrewing the

positioning bolt (14). Use the large allen key (1) to do

this. Continue until the swivel (12) (still attached to the

housing) comes completely loose from the bracket arm

(13). The positioning bolt (14) is held in the bracket arm

(13) by a plastic washer inside. Ensure this is the case.

13 13

Picture 3

3.3. Detach the swivel (12) from the housing by loosening its

four screws. Use the small allen key (2) to do this. The

four screws will be held in the swivel (12) by plastic

washers inside it.

3.4. When the whole assembly has come apart you should

have the parts as shown in Picture 3. Keep loose parts

safe.

3.5. Position the bracket arm (13) on the wall in the position

required and drill four fixing indicators. Remove the

bracket arm and drill the four holes (using an 11 mm

No.

9. Housing

10. White rubber seal

11. Widget

12. Swivel

13. Bracket arm

14. Positioning bolt

drill bit) to the depth and size (50 mm) of the plugs pro-

vided.

3.6. Route the cables through the rear of the bracket arm and

pull them out at the front. Pull out at least 60 cm of ca-

ble to complete the installation.

Caution: Make sure you do not damage the cable while

doing this. Check the cable for damages once you have

finished routing the cable through the bracket arm.

Warning: The cables may be damaged after routing

them. A damaged cable can cause serious damage to the

camera, the housing and/or other system equipment, it

also could seriously endanger the health and safety of

humans or animals.

3.7. Position the swivel (12) on the end of the bracket arm

(13) with the two cables coming through the open slot.

The front of the swivel is indicated by F on the swivel's

flat face. The rear is indicated by R, also on the swivels

flat face. Ensure that the swivel is positioned with F at

the front and R at the back. This is essential for further

correct assembly.

3.8. Now position the widget (11) inside the swivel (12) with

the cables coming through the opening. The front of the

widget is indicated by F and the rear by R. Match the F

and R on the widget with the F and R on the swivel, as-

suring that F remains at the front and R at the back.

3.9. Line up the positioning bolt (14) with the screw hole in

the widget (11) and tighten it up using the large allen

key (1).

3.10. Position the white rubber seal (10) on the flat face of the

swivel (12) by pushing the power cable through the off

centre hole on the left and the CAT.5 cable through the

off centre hole on the right. The two off centre holes

should be positioned towards the back (see Picture 4).

Power

3.11. Position the housing (9) on the swivel (12) with the

white rubber seal (10) in-between, the CAT.5 cable going

through the larger hole in the black board and the power

2/4

CAT.5

Two off centre holes

positioned at the back

Picture 4