Epever RTU 4G A Snelstarthandleiding - Pagina 2
Blader online of download pdf Snelstarthandleiding voor {categorie_naam} Epever RTU 4G A. Epever RTU 4G A 2 pagina's. Gprs transmission terminal
Ook voor Epever RTU 4G A: Snelstarthandleiding (2 pagina's)
Pagina afdrukkenHUIZHOU EPEVER TECHNOLOGY CO., LTD
Note: The EPEVER RTU 4G A supports 9~48V DC power. While a larger transient
current is needed when the wireless network sends the data, it is suggested to
adopt a DC power of 12V/500mA or above.
Note: If the EPEVER RTU 4G A is connected with the inverter or inverter/charger.
Connect the DB9 connector of the RS485 communication cable to the EPEVER
7. Connect the device to the EPEVER cloud server
The device connected with the EPEVER RTU 4G A can be added to the Cloud server by the PC or mobile APP. Take adding the device through the mobile APP as
an example (For the operations of adding a device by PC, refer to the EPEVER Cloud Server user manual).
CAUTION: Please get the Android or IOS version of the EPEVER cloud APP according to your phone system and install it successfully.
Step 1: Connect the EPEVER RTU 4G A with the device as chapter 5, Installation.
Step 3: Click the "Plant"
Step 2: Open the APP,
icon (it is the "Light" icon
click the "EPEVER Cloud"
instead when login in with
icon,
and
input
the
the streetlight account),
account to log in.
and select a project.
8. Troubleshooting
Faults
LED indicators are OFF
The network indicator is ON solid
Smoke emits along with a pungent
smell
Unregister on the network
Parameters can't be configured
Step 4: Click "
Device" on the "Plant
List" page.
Solutions
1. Check whether to supply power to the EPEVER RTU 4G A.
2. Check whether the power supply's poles are connected inversely. The EPEVER RTU 4G A is equipped with anti-reverse protection. The reverse
connection does not cause fatal damage. However, it affects the normal use before the correct connection is restored.
After power is on, the network indicator is on solid for 60 seconds. If it still cannot flash after 60 seconds, please check:
1. Check whether the SIM card is inserted correctly. 2. Check whether the GPRS service is activated.
The Network indicator is on solid again after running for a while:
1. Check whether the server status is normal. 2. Check whether the SIM card is loose or arrear.
The connected battery voltage exceeds the rated voltage, causing the internal components to burn out. Don't hesitate to contact the supplier in
time and send it to the manufacturer.
1. Check whether the SIM card is inserted correctly. 2. Check whether the SIM card has activated the GPRS service.
3. Check whether the input power is sufficient. Input power should be 12VDC/500mA.
1. Check whether the connection to the PC is correct. 2. Check whether the serial port selection is correct.
3
TEL: +86-752-3889706
RTU 4G A. Then connect the ends of the RS485 communication cable to the
battery and the device COM port. The master LORA module is no longer needed.
6. Specifications
Item
Network type
Coding method
Frequency
GPRS transmission rate
Network protocol
SIM card voltage
Antenna connector
Communication port
Serial port baud
Power
Power consumption
Environment temperature
Relative humidity
Dimension (L x W x H)
Mounting hole size
Net Weight
Electromagnetic
compatibility
> Add
Step 5: Select the device
to be added to the cloud
server.
Any changes without prior notice! Version number: 3.3
Website: www.epever.com
Specifications
GPRS class12
CS1 – CS4(Comply with SMG31bis)
GSM900/1800MHZ, CDMA: BC0, WCDMA: B1/B8,
TD-SCDMA: B34/B39, LTE TDD: B38/B39/B40/B41,
LTE FDD: B1/B3/B5/B8
150M
TCP/UDP/FTP/PPP/DNS
3V/1.8V
50Ω IPX connector
RS485
9600~115200bps
9~48VDC
Communication: <200mA/5V; Idle: <40mA/5V
-40~85℃
0~95%(Non-condensing)
101.2mm x 64mm x 26mm
∅3.2mm
54.0g
Electrostatic discharge immunity test, level 3
Anti-interference test, level 3
Step 7: Input the ID (or
scan the QR code) on the
Step
6:
Select
the
module label, and click
connected module (the
"Confirm" to enter the
EPEVER RTU 4G A).
Plant or Light project
page directly.
4