Axminster Woodturner's Clubman & Goliath Chucks Gebruikershandleiding - Pagina 14
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Axminster Woodturner's Clubman & Goliath Chucks. Axminster Woodturner's Clubman & Goliath Chucks 16 pagina's.
Pagina afdrukken
Woodturning Chuck Jaws Accessories...
FACEPLATE RINGS USED FOR
DOVETAIL JAWS
Made to match the
dovetail jaws, these
rings do away with
the need for a separate
faceplate on which to
mount a bowl blank
prior to turning the out-
side. Simply screw the
ring to the chosen blank
with woodscrews and
expand the dovetail
jaws into the recess in the centre of the ring.
Order no: 500166 Faceplate Ring A Jaws
Order no: 500167 Faceplate Ring B Jaws
Order no: 500168 Faceplate Ring C Jaws
Order no: 500170 Faceplate Ring F Jaws
AXMINSTER FOUR PRONG PARALLEL
DRIVE CENTRE (to suit DOVEC jaws)
The Axminster four prong parallel drive centre has
been designed to be used in the central bore of the
C jaws fitted to the Carlton, Super Precision,
Woodturner's and Clubman chucks. It has principally
been produced for those lathes that do not have a
hollow headstock, but
can also be used for
those combined jobs
where spindle turning is
necessary before mount-
ing the workpiece in the
chuck.
Order no: 410052
AXMINSTER BUTTON JAW
These jaws use eight conical rubber buttons
to securely pull back work onto the jaws.
They are intended for use with bowls
up to 9" in diameter. However, they
may not be suitable for bowls with
very thin edges as the pressure may
deform the bowl edges. The buttons
are white rubber so as not to mark
the workpiece and are "dovetailed"
to hold the workpiece firmly against
the plates.
Order no: 340956 (Jaws 250mm)
13
Order no: 340957 (Jaws 400mm)
AXMINSTER 150MM
WOOD JAW PLATES
A set of pre-drilled steel
quadrants onto which
self-made wooden jaws
can be mounted using
woodscrews. The wood-
en jaws can be used for
rechucking a bowl when
removing a dovetailed
recess or spigot, or for
producing a variety of
'jam' chuck-type holding
devices.
Order no: 910405
SCREW CHUCKS FOR USE WITH
DOVETAIL JAWS
A replaceable
stainless steel
parallel screw
mounted onto
a boss which fits into either the 62mm
recess of the A dovetails or the internal recess of the
C dovetail jaw. Particularly useful for the initial mount-
ing of bowl blanks whilst the outer form and the dove-
tail base are being shaped. Once this stage is com-
pleted the woodscrew chuck can be removed and the
bowl mounted directly into the chuck jaws in a matter
of seconds. Replacement screws are available for all
Axminster screw chucks and are listed below.
Order no: 810383 (To Fit A Dovetail)
Order no: 810385 (To Fit C Dovetail)
Order no: 910458 Small Screw
Order no: 210886 Medium Screw
Order no: 910466 Large Screw
CHUCK REMOVAL SPANNER
One
important
lesson for
woodturners to learn is not to use the
chuck key for removing the chuck from
the headstock; doing this can damage the
hole in the chuck as well as risking
breaking the key. This C spanner has
been specially produced for the 100mm
Clubman, Goliath and previous model
Woodturner's range of chucks. This
should be classed as essential equipment
for all users of these chucks.
Order no: 340220