AXTON ATB25RS Installatie- en bedieningshandleiding - Pagina 2

Blader online of download pdf Installatie- en bedieningshandleiding voor {categorie_naam} AXTON ATB25RS. AXTON ATB25RS 5 pagina's. High performance spare wheel subwoofer

Pagina afdrukken

Dear Customer

Thank you and congratulations on your purchase of the AXTON ATB25P. This active subwoofer

system exclusively uses very high quality parts and components. As with all high-quality car audio

components, professional installation is highly recommended. If you plan on installing this active

subwoofer by yourself, please read the following installation guide carefully, before you attempt the

installation. You should retain this manual, the packing and the purchasing receipt for future refer-

ence. For any further information about mounting, connecting or adjusting this subwoofer system,

please contact your AXTON dealer.

UNPACKING THE SYSTEM

Carefully remove all parts from the giftbox and check whether they are in good undamaged condition,

and match with the set contents listed below:

ATB25RS spare tire active subwoofer

Bass Boost remote control

1 Set of Plug&Play wire harness

1x M8 x 50 mm screw with nut (To fix the spare tire subwoofer in the stock spare wheel location)

1x M8 x 70 mm screw with nut (To fix the spare tire subwoofer in the stock spare wheel location)

Alignment plate

cable holder bar

velcro set to fix the spare tire active subwoofer

Installation guide

Please contact your authorized AXTON dealer, if the content of this set is incomplete, or parts of it

show signs of transport damage.

SPECIFICATIONS

n 10" active subwoofer

n Frequency response: 30 Hz – 150 Hz

n 115 W rms x 1 @ 2 ohms (<1% THD / 14.4V)

n Class-A/B amplifier

n Supply voltage: 11 – 15 V DC

n Fuse: ATC 15 A

n Variable lowpass filter: 50 Hz – 150Hz with 12 dB/oct.

n Selectable phase: 0 / 180°

n RCA input sensitivity: 150 mV

n High-Level input sensitivity: 1.2 V

n External bass level remote control

n Signal to noise ratio: > 92 dB

n Dimensions W x H: 360 x 147 mm

n Net Weight: 6.8 kg

– 2 –

SAFETY INSTRUCTIONS

1. This unit is designed to be used in a vehicle with a 12 V battery and negative ground.

2. Before any wiring, always remove the negative terminal of the battery to prevent short-circuiting. This

is also the last lead to be (re-)connected.

3. Do not disassemble or alter the unit in any way, because that will also void your warranty. Do not

attempt to repair or to service the unit yourself, but contact an authorized AXTON dealer instead.

4. Use only original accessories which are designed and manufactured for the unit, otherwise you will risk

to damage it. Install the unit according to the mounting manual and use only the supplied mounting

accessories. The forces of acceleration for accidents are sometimes huge. Incorrect mounted units are

a big risk for the driver and the passengers of the car, during an accident.

5. Protect the unit from water and other liquids, which can enter the casing. A short circuit or even fire

could be the result.

6. Before you replace a defective fuse, try to find the cause for the short circuit. Please pay attention

to the cables of the power supply! If the short circuit doesn't result from a failure of the power supply

or wiring, you can replace the defective fuse with a new one of identical value. If the short-circuit still

exists, please contact an authorized AXTON dealer.

7. Be careful not to drain the car battery while using the unit when the car engine is turned off. Because

the unit uses a considerable amount of energy and the battery will be charged only while the engine is

running, it might happen that the battery will discharge to a point where it's no longer possible to start

the engine.

8. If your car is parked in direct sunlight and there is a considerable rise in temperature inside the car,

allow the unit to cool off before operation.

9. Please pay attention to the volume inside your vehicle, because you are obliged to notice exterior

sounds like a police siren or you might face penalties in case of an accident or even lose your insurance

cover.

INSTALLATION

Use the supplied cable and wire harness and connect the outputs properly as shown in the High-

Level and Low-Level wiring diagram as following. Use only one of the audio inputs; otherwise, it

may lead to audio interference.

DIAGRAM High-Level

A) Take the wire side of the supplied connecting harness. Connect the white wire to the left (+),

white/black to the left (-) speaker wire; and the grey to right (+), grey/black to the right (-) speaker

wire. Finally connect this High-Level input adapter with the Plug&Play harness of the amplifier

panel of the ATB25RS

– 3 –