Axvue E662 Gebruiksaanwijzing

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Axvue E662. Axvue E662 2 pagina's. Video baby monitor with two way communication & temperature

Pagina afdrukken

INSTRUCTION MANUAL

AXVUE E662 Video Baby Monitor

with Two Way Communication & Temperature

Please read the following instructions and warnings carefully

Tools required for wall mount: Screwdriver and drill (not included)

Keep this instruction manual for future reference.

For technical support see FAQ page.

For adult use only.

WARNING

THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT SUPERVISION.

-Strangulation Hazard - Children have STRANGLED in cords. Keep this cord out of reach of children

(more than 3 feet away from the crib). Use enclosed Security Clips to help secure cord away from

baby's reach. Never use extension cords with AC adapters. Only use the AC adapters provided.

-When an adapter is plugged into an electrical outlet, do not touch the exposed end.

-Test monitor before ﬁrst use, periodically, and when changing location of the camera.

-Do not use monitor near water (such as bathtub, sink, etc.).

-Keep monitor away from heat sources (such as stoves, radiators, etc).

Make sure there is proper ventilation around all monitor components. Do not place on sofas,

cushions, beds, etc. which may block ventilation.

-This product is not a toy. Do not allow children to play with it. This product contains small parts.

Adult assembly required. Exercise care when unpacking and assembling the product.

BATTERY WARNING

-Use only the original rechargeable battery provided. Please contact AXVUE INC. for replacement

battery. Contact information can be found on last page of these instructions.

-Clean battery and product contacts prior to battery installation.

-Do not short-circuit supply terminals.

-Remove battery when product is stored for long periods of time or when battery is exhausted.

-Keep all batteries away from children.

-Dispose of exhausted battery properly.

WARNING:

STRANGULATION HAZARD - Children have STRANGLED in cords. Keep this cord out of reach of

children (more than 3 feet away from the crib). Use enclosed Security Clips to help secure cord

away from baby's reach. Never use extension cords with AC adapters. Only use the AC adapters

provided.

Features and components

MONITOR

*LED

Power & Low Battery

Model- E662

Get to know us at: www.axvue.com

1 Power / Video

2 LED*

3 Left

4 Talk Back / Zoom

5 Menu / OK

6 Speaker

7 Right

8 Volume Up

9 Volume Down

10 Microphone

11 Battery Compartment

12 Kickstand

13 DC Jack

Sound Lights

Adapter for monitor:

Features and components

CAMERA

Adapter for camera:

x12

STRANGULATION HAZARD - Children have STRANGLED in cords.

Keep this cord out of reach of children (more than 3 feet away

from the crib). Use enclosed Security Clips to help secure cord

away from baby's reach. Never use extension cords with AC

adapters. Only use the AC adapters provided.

Setup & use

Before using the monitor, charge the battery for 6-8 hours.

Step1: Turn camera power on by pressing and

holding Power / Code '

'button until

the power indicator lights.

Step2: Press and hold Power / Video

button on monitor for 5 seconds until the

AXVUE showed on the screen. Video should

immediately appear on screen.

If video does not appear, go to 'To pair monitor

and camera'. If video appears, the initial set up

test is completed, and you can install camera

according to the instructions below.

Install Camera: Place the camera on a ﬂat

surface, such as a bureau or shelf (Figure1) or

mount the camera on a wall (Figure 2). For

example: On the desk or cabinet or ﬁxed to the

wall, make sure that at least 3 feet from the

crib, power line should be placed above or

behind the camera, adjust the camera angle

until the display see the entire crib, or the best

line of sight you think.

WALL-MOUNT

1. Pre-drill a hole in the wall, a 3/16" (4.8mm) drill bit.

2. Insert the wall anchor into the hole and with a hammer, tap gently on the

end until the wall anchor is ﬂush with the wall.

3. Tighten screw until only 1/4" (6.2mm) of the screw is exposed.

4. Insert camera adapter into the camera's adapter jack.

5. Slide the back of the camera down onto the screw until the camera is secure to the wall.

6. Plug the adapter into a standard electrical outlet.

7. Secure the cord to the wall by using the security clips to keep cord away from baby's reach.

TO USE PLUGGED-IN MODE

Step 1: Place the monitor in the room from which you want to monitor your baby (ie., living room or

bedroom). Plug the monitor AC adapter into the AC adapter jack and other end into standard

electrical outlet.

Step 2: Press and hold Power / Video

button for 5 seconds to power up until the AXVUE logo or

video appears on screen.

Step 3: For audio and no video, press the Power / Video

Step 4: To turn the monitor oﬀ completely, press and hold the Power / Video

TO USE PORTABLE / BATTERY MODE

Before using the monitor, charge the battery for 6-8 hours.

Step 1: Charge the battery for 6 hours at least before using the monitor in portable mode.

Step 2: Make sure camera adapter is plugged into the camera.

Step 3: The battery life can be up to 8 hours if fully charged.

Battery life will be weakened if recharging constantly. Remove battery if long time of non-use, or exhausted.

TO PAIR MONITOR AND CAMERA ( ADD A CAMERA )

The monitor and the camera are paired prior to the shipment. If the monitor and camera are

found not paired for some reason, follow steps below:

Step 1: Make sure the monitor is at the same area with the camera.

Step 2: Make sure the camera AC adapters are plugged in.

Step 3: Press Power / Video

for 5 seconds to power on the monitor.

Step 4: Press Menu / OK

shortly to enter menu, then press Right

function and Menu / OK

to conﬁrm.

Step 5: Using the Left

or Right

to highlight ADD CAM

Step 6: Choose the identifying number to be assigned on the camera.

Step 7: Press the Menu / OK

button again to start pairing and the red light will ﬂash.

VOX

Step 8: Press Power/Code '

'on the camera until the power indicator ﬂashes.

Step 9: Waiting 3 seconds, the green light stop ﬂashing once paired successfully and the video will appear.

(continued)

1 Nighttime LEDs

2 Lens

3 Power Indicator

4 Microphone

5 Speaker

6 Power / Code

7 Temperature Sensor

8 DC Jack

WARNING

Figure 1

3 feet

Fixing cable

with clip

Figure 2

button.

button for 5 seconds.

to highlight the camera option

and press Menu / OK

to conﬁrm.

Red LED will ﬂash