EPSON LQ-680Pro
8. Turn the ribbon-tightening knob again to remove any slack
in the ribbon and to make sure the ribbon moves freely.
9. Close the printer cover.
The printer pauses and cannot print when the printer
cover is open.
Changing the Default Settings
While you can often set the default settings through your
application software or printer driver, you may need to change a
default setting from the printer's control panel using the default
setting mode. The table below lists the default settings (in bold)
and options you can select in this mode.
Settings
Page length for tractor
Skip over perforation
Auto tear-off
Auto line feed
Print direction
Software
0 slash
High speed draft
I/F mode
Auto I/F wait time
Parallel I/F bidirectional mode
Packet mode
Auto CR (IBM 2390 Plus)*
A.G.M. (IBM 2390 Plus)*
14 - EPSON LQ-680Pro
Options
Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8,
8.5, 11, 70/6, 12, 14, 17
On, Off
On, Off
On, Off
Bi-D, Uni-D, Auto
ESC/P2, IBM 2390 Plus
0
0,
On, Off
Auto, Parallel, Optional
10 seconds, 30 seconds
On, Off
Auto, Off
On, Off
On, Off
Settings
Character table*
International character set for
Italic table
Font
Manual feed wait time
Buzzer
Overlapping forms
* These settings take effect only when IBM 2390 Plus emulation is
selected.
Follow the steps below to enter the default setting mode and
change the printer's default settings.
To print all the instructions, you need 5 sheets of letter-
or A4-size single-sheet paper or 5 pages of continuous
paper. If you use single sheets without a cut-sheet
feeder, you need to load a new sheet each time the
printer ejects a printed sheet.
1. Make sure paper is loaded and the printer is turned off.
Whenever you turn off the printer, wait at least 5
seconds before turning it back on; otherwise you may
damage the printer.
2. While holding down the
The printer enters the default setting mode and prints the
language selection instructions.
3. If you need to select a different language, press the
button until the
Font
as described in the language selection instructions.
4. Press the
Tear Off/Special Paper
language selection and print the current default settings.
5. If you do not need to change any settings, go to step 6.
If you want to change any of the default settings, press the
button to print the instructions (three pages) in
Tear Off
the language you selected.
Follow these instructions to change the default settings
using the buttons on the printer's control panel.
11/00
Options
Standard model:
Italic, PC 437, PC 850, PC 860,
PC 863, PC 865, PC 861, BRASCII,
Abicomp, Roman 8, ISO Latin 1,
PC 858, ISO 8859-15,
All other models: Italic, PC 437,
PC 850, PC 437 Greek, PC 853,
PC 855, PC 852, PC 857, PC 864,
PC 866, PC 869, MAZOWIA,
Code MJK, ISO 8859-7, ISO Latin 1T,
Bulgaria, PC 774, Estonia,
ISO 8859-2, PC 866 LAT, PC 866 UKR,
PC APTEC, PC 708, PC 720,
PC AR864, PC 860, PC863, PC 865,
PC 861, BRASCII, Abicomp,
Roman 8, ISO Latin 1, PC 858,
ISO 8859-15, PC 771
Italic U.S.A., Italic France, Italic
Germany, Italic U.K., Italic Denmark1,
Italic Sweden, Italic Italy, Italic Spain1
OCR-B, Orator, Orator-S, Script C,
Roman T, Sans Serif H
0.5 second, 1 second, 1.5 seconds,
2 seconds
On, Off
On, Off
button, turn on the printer.
Font
lights indicate the language you want,
button to confirm your
Font
Pagina afdrukken