ABB XRC G5 Snelstarthandleiding - Pagina 2

Blader online of download pdf Snelstarthandleiding voor {categorie_naam} ABB XRC G5. ABB XRC G5 2 pagina's.

Pagina afdrukken

XSeries

Quick Start

Power modes

The XFC and XRC can support either of two power modes.



Battery mode: The primary power source to the device is

a 12 volt sealed lead acid battery with nominal 12 volt

solar panel charger.



External power mode: The primary power source to the

device is an outside power supply (14.5 to 15.5 Vdc

maximum).

WARNING – Bodily injury

Do not connect the

battery/charger or external power supply to the

electronic board until all wiring is complete.

Install battery and charger

To operate the XFC or XRC in battery power mode, install the

battery and solar panel charger as follows.

Install the battery

The battery mounts inside the flow computer enclosure. Before

installation, inspect for damage both the power cables (where they

terminate on the battery) and the connectors.

Required material:



One (1) battery with cable attached

Install the battery:

Open the hinged door on the XFC or XRC. Locate the battery

shelf.

Place the battery on the compartment shelf.

DANGER – Serious damage to health/risk to life: Do

not allow the battery terminals to come in contact with any

metal surface. This could result in sparks, property damage,

and possible explosion.

Install the solar panel

The solar panel is designed to be mounted outdoors on a 2

inch pipe. After the flow computer is pipe-mounted, install the

solar panel on the upper end of the mounting pipe. Add a pipe

extension if necessary. For wall- or direct-mount installations,

mount the solar panel on a stand-alone pipe or on the top or

side of a meter house.

IMPORTANT NOTE: For best charging, place the solar panel in

full sun all day. Clean the solar panel on a regular basis to

ensure maximum charging.

IMPORTANT NOTE: For Wi-Fi

and Bluetooth

refer to the user manual.

Required materials:



One (1) solar panel with cable



One (1) solar panel mounting kit (includes U-bolts,

brackets, and hardware)



Mounting pipe extension and coupling if required (length

determined by technician depending on the size of the

solar panel)



Nylon tie wraps

NOTICE – Equipment damage. Exercise caution when

handling the solar panel to avoid damage.

Install the solar panel:

Verify that the solar panel is operating properly before

installation:

Check the solar panel using a digital voltmeter to verify

polarity and output voltage.

If the measured output voltage is within the

manufacturer's specification, continue with the installation.

If the measured voltage is out of specification, contact

ABB for a replacement panel.

Install the mounting bracket on the solar panel using the

provided hardware.

If installation requires a mounting pipe extension:

Attach the pipe coupling to the top end of the flow

computer mounting pipe.

Securely tighten the pipe coupling.

Attach the extension pipe to the pipe coupling.

Attach the solar panel mounting bracket to the top end of the

mounting pipe with the U-bolts and associated mounting

hardware. Do not tighten completely.

Insert the panel cable into the enclosure leaving enough length

to reach the CHRG terminal block.

Wire and power the device

For wiring, refer to Figure 1 or Figure 2 on the reverse side.

Wire all peripherals to the electronic board.

If battery powered:

Connect the battery to the BATT connector (J1 on the XFC,

or J16 on the XRC).

Remove the connector from the CHRG terminal block (J5

on the XFC, or J17 on the XRC).

Wire the solar panel cable wires into the removed

connector with correct polarity (+, -).

Reinsert the connector into the CHRG terminal.

If externally powered, connect the outside power source to the

BATT connector (J1 on the XFC, or J16 on the XRC).

Verify the power-on sequence on the LCD.

Local communication with the device

Establish initial communication with the XFC or XRC with a

connections,

direct connection to the RS-232 (MMI) or USB ports.

Communication on the USB port is faster.

IMPORTANT NOTE: Use PCCU32 software version 7.65 or

newer to connect and configure XSeries

PCCU32 is already installed in the PC or laptop. PCCU32 has

context-sensitive online help. Click Help on the screen of

interest for details.

Local communication using serial or USB port

IMPORTANT NOTE: Use the appropriate cable for each port.

Contact ABB to order recommended cables: For USB, order Y-

adapter cable (1803009-001). For serial, for laptops without RS-

232 ports, order the Digi® Edgeport®/1 serial-to-USB converter

(1801382-001).

Connect the laptop or PC running PCCU32 to the flow

computer with an MMI cable (RS-232) or a USB cable.

Start PCCU32.

Click the Setup icon on the PCCU toolbar, or click

Operate>Setup>System Setup.

Define the local connection parameters:

Under Communications, select Serial port.

Under Connection Parameters, on the PCCU Com Port

drop-down list, select the port on the PC or laptop

assigned to the local connection.

Click Close to exit connection setup and return to the

main PCCU screen.

Click Entry on the top PCCU toolbar to establish

connection.

Configure basic parameters or enable other

communication interfaces.

Local communication using Ethernet

On the PCCU Entry mode navigation tree, select

Communications>Ethernet.

Select the Network Adapter checkbox.

Click Send. Click OK to confirm.

IMPORTANT NOTE: Enabling Ethernet (Network Adapter)

does not require a warm restart.

Connect the Ethernet cable from the laptop to the XFC

or XRC.

Click Re-read to refresh the screen and verify that the

Ethernet Status displays "Ready".

Click Close to exit Entry mode and close serial

connection.

To connect using Ethernet, click the Setup icon on the

PCCU toolbar.

Under Communications, select TCP/IP.

Under Connection Parameters, type the IP address:

169.254.0.11

10. Click Close to exit connection setup and return to the

main PCCU screen.

11. Click Entry on the top PCCU tool bar to reestablish

connection.

12. Proceed with configuration.

XSE RI ES G5 Q U I C K STA RT G UI DE | 2 1 0 6 14 1 M N A A

devices. Ensure