Crest Audio BFP1FM Snelstarthandleiding - Pagina 2
Blader online of download pdf Snelstarthandleiding voor {categorie_naam} Crest Audio BFP1FM. Crest Audio BFP1FM 4 pagina's. Tv wall mount
Pagina afdrukken
Tools Required
DRYWALL INSTALLATION (TIMBER SUPPORTS):
• Adjustable spanner/socket set
• Philips head screwdriver
• Power drill
• High speed 5mm drill bit
• Pencil
Using the Stud Finder with Spirit Level
HOW IT WORKS:
•
•
studs and wooden frames
•
object is detected
•
WOOD: up to 20mm, wood should be detected based
on the thickness of the drywall less than 20mm
METAL: up to 50mm, metal should be detected based
on the thickness of the drywall less than 50mm
VOLTAGE: up to 70mm, AC wires should be detected
based on the thickness of drywall less than 70mm
Step 1: Fix Wall Plate to Wall
A. INSTALLING IN DRYWALL (TIMBER SUPPORTS)
WARNING: If attaching this TV Wall Mount using this method, you MUST spread the Wall Plate across 2 wall
studs. Wall studs can be 450mm or 600mm apart depending upon the position of the wall and the geographical
State you live in. The Crest Company will not accept any damages that may occur if only 1 stud is used.
1. Locate the centre of 2 adjacent timber studs using the supplied stud finder with spirit level.
(NOTE: You must use the centre of the stud to avoid cracking or splitting the timber during installation).
2. Mark a minimum of 4 fixing holes over stud centres using the Wall Plate as a guide - position 2 at either end of the
Wall Plate. Ensure plate is level.
3. Pre-drill holes to a minimum depth of 60mm using high speed 5mm drill bit (see Figure 1). If installing in hardwood,
larger diameter and deeper holes may be required.
4. Attach the Wall Plate by inserting lag bolts (W-A) through round washers (W-C) and then through the Wall Plate.
Do not over tighten.
B. INSTALLING IN MASONRY
WARNING: Ensure you have a minimum of 35mm of actual concrete or brick thickness in the hole for the anchors.
Do not drill into mortar joints. Installer must verify that the supporting surface will safely support the combined
weight of the Wall Mount and TV. The Crest Company holds no responsibility for incorrectly installed TV Wall Mounts.
1. Mark a minimum of 4 fixing holes (preferably 6) using the Wall Mount plate as a guide - position 2 at either end of the Wall Plate.
Ensure plate is level.
2. Pre-drill holes to a minimum depth of 60mm using an 10mm masonry drill bit. Clean out holes.
3. Fully insert the concrete anchors (W-B) into the drill holes. Tap in with hammer if required.
4. Attach the Wall Plate by inserting lag bolts (W-A) through round washers (W-C) into each concrete anchor (W-B).
Do not over tighten.
Use the supplied stud finder
with spirit level to level
your TV Wall Mount
before installation
MASONRY INSTALLATION:
• Adjustable spanner/socket set
• Philips head screwdriver
• Power drill with hammer function
• 10mm masonry drill bit
• Pencil
• Hammer
INSTRUCTIONS:
1. Keep the stud finder in touch with the drywall.
2. Press the ON/OFF button until the LED indicator turns
RED. Do not move the stud finder.
3. Wait 3 to 10 seconds until the LED indicator turns GREEN,
then start moving the stud finder slowly on the drywall.
4.
object is detected.
5. Mark a point on the wall using your pencil, then continue
moving the stud finder until the GREEN LED indicator
6. The midpoint between the two marks on your wall
is the centre of the stud.
STUD
Find the wood stud,
metal or voltage before
TV Wall Mount installation