Sharp Carousel R-880F Servicehandleiding - Pagina 28
Blader online of download pdf Servicehandleiding voor {categorie_naam} Sharp Carousel R-880F. Sharp Carousel R-880F 48 pagina's. Double grill convection microwave oven
Ook voor Sharp Carousel R-880F: Servicehandleiding (3 pagina's)
Pagina afdrukken
R-880F(S)
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE
WARNING: Avoid possible exposure to microwave energy. Please follow the instructions below before
operating the oven.
1. Disconnect the oven from power supply.
2. Make sure that a definite "click" can be heard when the
microwave oven door is unlatched. (Hold the door in a
closed position with one hand, then push the door open
button with the other, this causes the latch leads to rise,
it is then possible to hear a "click" as the door switches
operate.)
3. Visually check the door and cavity face plate for dam-
age (dents, cracks, signs of arcing etc.).
Carry out any remedial work that is necessary before
operating the oven.
Do not operate the oven if any of the following conditions
exist;
Please refer to 'OVEN PARTS, CABINET PARTS, CONTROL PANEL PARTS, DOOR PARTS', when carrying out any
of the following removal procedures:
To prevent an electric shock, take the following
manners.
1. Before wiring,
1) Disconnect the power supply.
2) Open the door and wedge the door open.
3) Discharge the high voltage capacitor and wait for
60 seconds.
2. Don't let the wire leads touch to the following parts;
1) High voltage parts:
Magnetron, High voltage transformer, High volt-
age capacitor and High voltage rectifier assem-
bly.
2) Hot parts:
Oven lamp, Magnetron, Grill heaters, Bottom
To remove the outer case proceed as follows.
1. Disconnect oven from power supply.
2. Open the oven door and wedge it open.
3. Remove the two (2) screws holding the back plate to
the oven cavity rear plate.
4. Remove the back plate.
5. Remove the five (5) screws from rear and along the
side edge of case.
6. Slide the entire case back about 3cm to free it from
(HIGH VOLTAGE CAPACITOR, HIGH VOLTAGE RECTIFIER ASSEMBLY AND HIGH VOLTAGE FUSE)
To remove the components, proceed as follows.
1. CARRY OUT 3D CHECKS.
2. Disconnect all the leads and terminals of high voltage
rectifier assembly from the high voltage capacitor.
WARNING FOR WIRING
OUTER CASE REMOVAL
HIGH VOLTAGE COMPONENTS REMOVAL
1. Door does not close firmly.
2. Door hinge, support or latch hook is damaged.
3. The door gasket or seal or damaged.
4. The door is bent or warped.
5. There are defective parts in the door interlock system.
6. There are defective parts in the microwave generating
and transmission assembly.
7. There is visible damage to the oven.
Do not operate the oven:
1. Without the RF gasket (Magnetron).
2. If the wave guide or oven cavity are not intact.
3. If the door is not closed.
4. If the outer case (cabinet) is not fitted.
heater, High voltage transformer and Oven cav-
ity.
3) Sharp edge:
Bottom plate, Oven cavity, Waveguide flange,
Chassis support and other metallic plate.
4) Movable parts (to prevent a fault)
Fan blade, Fan motor, Switch, Switch lever, Open
button, Turntable motor, Convection motor.
3. Do not catch the wire leads in the outer case cabinet.
4. Insert the positive lock connector certainly until its
pin is locked. And make sure that the wire leads
should not come off even if the wire leads is pulled.
5. To prevent an error function, connect the wire leads
correctly, referring to the Pictorial Diagram.
retaining clips on the cavity face plate.
7. Lift the entire case from the oven.
8. Discharge the H.V. capacitor before carrying out any
further work.
9. Do not operate the oven with the outer case removed.
N.B.; Step 1, 2 and 8 form the basis of the 3D checks.
CAUTION: DISCHARGE HIGH VOLTAGE CAPACITOR
B E F O R E
COMPONENT OR WIRING.
3. Disconnect the high voltage fuse from the high voltage
transformer.
4. Now, the high voltage fuse is free.
5. Remove one (1) screw holding earth side terminal of
26
T O U C H I N G
A N Y
O V E N