Sharp EBR-9900W Instructie - Pagina 2
Blader online of download pdf Instructie voor {categorie_naam} Sharp EBR-9900W. Sharp EBR-9900W 16 pagina's. Built-in kit
Ook voor Sharp EBR-9900W: Instructie (17 pagina's)
Pagina afdrukken
1. (For U.K. use)
A cut-out will have to be provided in the side of the kitchen cabinet for the plug of the oven.
N.B.The mains plug must be accessible after installation or an all-pole switch disconnection must be
provided with a contact separation of at least 3 mm in each pole.
(For Continental use)
The electric outlet must be installed at 150 mm high from the floor of the built-in cabinet and at 50 mm
from the right wall of the built-in cabinet as shown in Fig. 1. The mains plug must be accessible after
installation or the oven must be connected to an electric circuit provided with an all-pole switch (contact
gap no less than 3 mm) to disconnect the oven in case of danger. A safety-device like a fuse in the
installation may be used as a switch.
2. Remove the built-in kit from the package.
3. Set the spacing brackets 1 on the shelf along the right and left walls of the kitchen cabinet, adjusting
the front ends of the shelf and the spacing brackets, and attach them with the four screws
shown in Fig.1.
Caution:
The arrow marks on each spacing bracket should be pointing towards you.
4. Place the exhaust duct 2 on the ceiling of the kitchen cabinet along the back wall of the cupboard D and
left wall of the kitchen cabinet without the clearance as shown in Fig.1 and 2. Secure to the ceiling of the
kitchen cabinet with two screws
5. Remove the backing paper from the cushion 6. Attach the cushion 6 to the edge of the exhaust duct
3 as shown in Fig. 4.
6. Insert two tabs of the exhaust duct 2 into the slits of the exhaust duct 3. And fold the tabs.
7. Remove the screw E from the oven as shown in Fig. 5.
8. Let the power supply cord pass through the hole of the lower side of the intake duct 4 as shown in Fig. 6.
9. Install the intake duct 4 to the rear of the oven with two screws
in Fig. 6.
Avoid pinching the power supply cord between the oven and the intake duct 4.
Caution:
10. Install the intake duct 5 to the rear of the oven with three screws
Avoid pinching the power supply cord between the oven and the intake duct 4.
Caution:
11. Remove the backing paper from the three cushions 7, 8 and 9. Attach the cushion 7 at the left side along
the intake duct 4 then attach the cushion 8 at the top of the intake duct 4, and along the left side of the
cushion 7 and the oven as shown in Figs. 8-a and 8-b. Attach the cushion 9 to the top of the oven as shown
in Figs 8-a and 8-b.
12. (For U.K. use)
Place the oven on a table/stand positioned in front of the kitchen cabinet. If you do not prepare the table/
stand, two persons are required. One to hold the oven whilst the other feeds the power supply cord
through the prepared cut out.
(For Continental use)
Place the oven on a table/stand positioned in front of the kitchen cabinet.
If you do not prepare the table/stand, two persons are required. One to hold the oven whilst the other
connects it to the power supply.
13. Connect the oven to the power supply.
Caution: a. In U.K., connect the oven to the power supply 230-240 V, 50 Hz.
b. In the Continent, connect the oven to the power supply 230 V, 50 Hz.
14. Make sure the oven is on the spacing brackets on the shelf of the kitchen cabinet. Then adjust the position
of the oven so that the feet of the oven are fitted into the recesses of the spacing brackets as shown in
Fig. 2.
Caution:
Make sure that the power supply cord does not touch the air vent openings behind the oven.
15. Place the built-in frame element
horizontally. Secure loosely to the kitchen cabinet with two screws
16. Insert two built-in frame side elements
D tightly as shown in Fig. 9. Check location by measuring distance between right
And secure two screws
and left built-in frame side elements
Note: Fit the hole of the built-in frame side element
17. Install the second built-in frame element
oven. And secure the built-in frame element
to the kitchen cabinet with two screws
Caution:
Make sure that 6.5 mm of the frames (upper and lower) and cabinet overlap each other as
shown in Fig. 11, or the kitchen cabinet door may touch the built-in frame elements.
INSTALLATION INSTRUCTIONS
B from below as shown in Fig. 3.
0 on top of the oven making sure that it is level both vertically and
A between the built-in frame element 0 and the kitchen cabinet.
A . The distance is stated in Fig. 10.
A to the screw D when inserting.
0 over the built-in frame side elements A at bottom edge of the
0 through the holes of the built-in frame side elements A
D as shown in Fig. 9.
2
C and E (removed at step 7) as shown
C as shown in Fig. 7.
D as shown in Fig. 9.
B , as