Sharp 13K-M150 Servicehandleiding - Pagina 3

Blader online of download pdf Servicehandleiding voor {categorie_naam} Sharp 13K-M150. Sharp 13K-M150 24 pagina's.

Pagina afdrukken

IMPORTANT SERVICE SAFETY PRECAUTION

RETBEFOREURNING THE RECEIVER

(Fire & Shock Hazard)

Before returning the receiver to the user, perform

the following safety checks.

1. Inspect all lead dress to make certain that leads are

not pinched or that hardware is not lodged between

the chassis and other metal parts in the receiver.

2. Inspect all protective devices such as non-metallic

control knobs, insulating materials, cabinet backs,

adjustment and compartment covers or shields,

isolation resistor-capacity networks, mechanical

insulators, etc.

3. To be sure that no shock hazard exists, check for

leakage current in the following manner.

Plug the AC cord directly into a 120 volt AC outlet,

(Do not use an isolation transformer for this test).

Using to clip leads, connect a 1.5k ohm, Iê watt

resistor paralleled by a 0.15µF capacitor in series

with all exposed metal cabinet parts and a known

earth ground, such as electrical conduit or electrical

ground connected to earth ground.

Use an AC voltmeter having with 5000 ohm per volt,

or higher, sensitivity to measure the AC voltage drop

across the resistor.

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2

SAFETY NOTICE

Many electrical and mechanical parts in television

receivers have special safety-related characteristics.

These characteristics are often not evident from visual

inspection, nor can protection afforded by them be

necessarily increased by using replacement components

rated for higher voltage, wattage, etc.

Replacement parts which have special safety

characteristics are identified in this manual; electrical

components having such features are identified by "

and shaded areas in the Replacement Parts Lists and

Schematic Diagrams.

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2

(Continued)

Connect the resistor connection to all exposed metal

parts having a return to the chassis

(antenna, metal cabinet, screw heads, knobs and

control shafts, escutcheon, etc.) and measure the

AC voltage drop across the resistor.

AII check must be repeated with the AC line cord

plug connection reversed. (IF necessary, a non-

polarized adapter plug must be used only for the

purpose of completing these check.)

Any current measured must not exceed 0.5 milliamp.

Any measurements not within the limits outlined

above are indicative of a potential shock hazard and

corrective action must be taken before returning the

instrument to the customer.

TO EXPOSED

METAL PARTS

For continued protection, replacement parts must be

identical to those used in the original circuit.

The use of substitute replacement parts which do not

have the same safety characteristics as the factory

recommended replacement parts shown in this service

manual, may create shock, fire, X-radiation or other

hazards.

13K-M100/150

CK13M10/15

VOLTMETER

1.5k ohm

10w

0.15µF

TEST PROBE

CONNECT TO

KNOWN EARTH

GROUND