Sharp CD DHS1050P Bedieningshandleiding - Pagina 11

Blader online of download pdf Bedieningshandleiding voor {categorie_naam} Sharp CD DHS1050P. Sharp CD DHS1050P 17 pagina's. Mini component system

Pagina afdrukken
Sharp CD DHS1050P Bedieningshandleiding

Listening to the radio

TUNER
(BAND)
5
4
3
2
1
TAPE
TIMER
POWER
ON/ STAND-BY
iPod/iPhone
CD
TUNER
(BAND)
TAPE
TUNING
AUDIO IN
USB
TUNING
TUNER(BAND)
TUNING
PRESET
Tuning
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TUNER (BAND) button repeatedly to select
the desired frequency band (FM or AM).
3
Press the TUNING (
desired station.
Manual tuning:
Press the TUNING (
required to tune in to the desired station.
Auto tuning:
When the TUNING ( or ) button is pressed for more
than 0.5 seconds, scanning will start automatically
and the tuner will stop at the fi rst receivable broadcast
station.
Notes:
When radio interference occurs, auto scan tuning may
stop automatically at that point.
Auto scan tuning will skip weak signal stations.
To stop the auto tuning, press the TUNING (
button again.
To receive an FM stereo transmission:
Press the TUNER (BAND) button to display the "ST"
indicator.
"
" will appear when an FM broadcast is in stereo.
If the FM reception is weak, press the TUNER (BAND)
button to extinguish the "ST" indicator. The reception
changes to monaural, and the sound becomes
clearer.
OPEN / CLOSE
MINI COMPONENT SYSTEM
CD-DHS1050P
REMOTE
SENSOR
OPEN / CLOSE
VOL.
VOL.
5
4
3
PRESET
2
1
PRESET
ON/STAND-BY
TAPE
DISPLAY
MENU
(TV OUT)
DISPLAY
CD
TUNER(BAND)
TAPE
AUDIO IN
USB
X-BASS
BASS/TREBLE
TUNING
VOL
FOLDER
PLAY MODE
PRESET
ENTER
PRESET
CLOCK/TIMER
MEMORY
DEMO
DIMMER
CLEAR
SLEEP
MUTE
MEMORY
PRESET
or
) button to tune in to the
or
) button as many times as
Memorizing a station
You can store 40 AM and FM stations in memory and
recall them at the push of a button. (Preset tuning)
1
Perform steps 1 - 3 in "Tuning".
2
Press the MEMORY
button
to
preset
tuning
mode.
3
Within 30 seconds, press the PRESET (
to select the preset channel number. Store the stations
in memory, in order, starting with preset channel 1.
4
Within 30 seconds, press the MEMORY button to
store that station in memory. If the "MEMORY" and
preset number indicators disappear before the station
is memorized, repeat the operation from step 2.
5
Repeat steps 1 - 4 to set other stations, or to change
a preset station. When a new station is stored in the
memory, the station previously memorized for that
preset channel number will be erased.
Note:
The backup function protects the memorized stations for a
few hours should there be a power failure or the AC power
cord become disconnected.
To recall a memorized station
Press the PRESET (
seconds to select the desired station.
To scan the preset stations
The stations saved in the memory can be scanned
automatically. (Preset memory scan)
1
Press the PRESET (
0.5 seconds. The preset number will fl ash and the
programmed stations will be tuned in sequentially, for
5 seconds each.
2
Press the PRESET (
desired station is located.
To erase entire preset memory
1
Press the ON/STAND-BY button to enter the stand-by
mode.
2
While pressing down the OPEN / CLOSE button and
TUNING
until "TUNER CLEAR" appears.
TUNING
OPEN / CLOSE
or
)
E-10
enter
the
saving
or
) button for less than 0.5
or
) button for more than
or
) button again when the
button, press the TUNER (BAND) button
TUNER
(BAND)
TAPE
or ) button