Crestron CP3N Snelstarthandleiding - Pagina 2

Blader online of download pdf Snelstarthandleiding voor {categorie_naam} Crestron CP3N. Crestron CP3N 2 pagina's. Automated processors
Ook voor Crestron CP3N: Snelstarthandleiding (2 pagina's), Snelstarthandleiding (8 pagina's)

Pagina afdrukken

Configure the Control System

The CP3 can be configured using Crestron Toolbox™ software

and the built-in, web-based setup tool.

1. Use Crestron Toolbox to set the time zone. For details,

refer to the Crestron Toolbox help file.

2. Use Internet Explorer

browser to navigate to http://xxx.

xx.xx.xxx/setup, where xxx.xx.xx.xxx is the IP address of

the control system. The control system's welcome screen

is displayed.

NOTE:

The web-based setup tool is accessible only from

Internet Explorer.

NOTE:

If a security warning is displayed, click Install to

continue.

As of the date of manufacture, the product has been tested and found to comply with specifications for CE marking.

These products are Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:

(1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Caution: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's

authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

GUIDE

3. Click Setup to display the CP3 setup menu. The CP3

setup menu displays the IP address, hostname, and MAC

address of the device. It also allows access to various

setup and programming screens.

4. From the CP3 setup menu, click the following options to

configure the control system:

• Ethernet Setup configures the CP3's Ethernet

settings and displays DHCP, hostname, IP address,

subnet mask, default router, domain, and MAC

address settings. In the Ethernet setup menu, there

are additional options:

• Click Advanced Settings to specify DNS

servers, web server settings, and SSL settings.

• Click MyCrestron Dynamic DNS to configure

the myCrestron.com Dynamic DNS service.

Rack Mounting Safety Precautions

• Elevated Operating Ambient Temperature: If the unit is installed in a closed or multiunit rack assembly, the operating ambient

temperature of the rack environment may be greater than room ambient temperature. Therefore, consideration should be

given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the

manufacturer.

• Reduced Airflow: Installation of the equipment in a rack should be such that the amount of airflow required for safe operation

of the equipment is not compromised.

• Mechanical Loading: Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to

uneven mechanical loading.

• Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and the effect that

overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment

nameplate ratings should be used when addressing this concern.

• Reliable Earthing: Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to

supply connections other than direct connections to the branch circuit (e.g., use of power strips).

Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive, non-transferable Software Development Tools

License Agreement. Crestron product operating system software is licensed to Crestron dealers, CSPs, and end-users under a separate End-User License Agreement. Both of these Agreements

can be found on the Crestron website at www.crestron.com/legal/software_license_agreement.

The specific patents that cover Crestron products are listed at patents.crestron.com.

Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

Crestron, the Crestron logo, 3-Series, and Crestron Toolbox are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Internet

Explorer is either a trademark or registered trademark of Microsoft Corporation in the United States and/or other countries. UL and the UL logo are either trademarks or registered trademarks

of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the

entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or

photography.

This document was written by the Technical Publications department at Crestron.

• Click Ethernet Diagnostics to test Ethernet

communications.

• Click Reboot to reboot the CP3.

• Application Setup selects programs to be loaded

on startup and controls which program(s) are

running.

• Input/Output Control configures the COM ports,

operates the relays, and monitors the Versiports.

• Diagnostics displays information about the

connected devices, hardware configuration, and

error logs.

• About displays firmware information.

Click

to return to the previous screen.

Learn More

Visit the product page on the Crestron website

(www.crestron.com) for additional information. Use

a QR reader application on your mobile device to

scan the QR images.

Crestron Electronics

15 Volvo Drive, Rockleigh, NJ 07647

888.CRESTRON | www.crestron.com

The product warranty can be found at www.crestron.com/warranty.

DOC. 7714C (2042569) 02.16

Specifications subject to change without notice.

CP3

CP3N